Lots of 500+ parts
#1
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jun 2006
Posts: 887
Likes: 0
Received 0 Likes
on
0 Posts
Lots of 500+ parts
Due to lack of time and recent bad health I'm not going to complete my project car. Everything is up for sale. Many parts are new or trial fitted only.
Gutted to be doing this and likely to lose a fortune but such is life.
All prices are + postage or collection from Aberdeen.
I'm willing to meet where possible or have parts passed on as long as they are paid for first.
If using paypal please cover fee's.
The engine was assembled into a Long block and timed up by Steven Darley.
It was never run or even fitted since I collected it earlier this year from Steven's but is now split to try and get everything sold on.
2.1 Short Engine
EJ20 CDB c/with under piston squirters.
Block was stripped, cleaned and inspected. Machined to take crank. Decked and bored / honed to suit pistons.
Lateral performance 2.1 stroker kit c/with Wiseco pistons, ACL race bearings, brand new Nitrided x-drilled EJ257 crank, all new genuine seals etc.
Refurbished water x-over pipe with new o-rings again from Lateral.
All supplied built from Lateral.
£2,600 Prov sold to Cullenmin
New timing belt kit including all idlers and tensioner (2 piece) and Power Enterprise Kevlar timing belt
£150 Prov sold to Chris Allsop
New Cosworth Billet Timing belt guide (Cost £60)
£40 Prov sold to Cullenmin
Samco hoses from and to the water pump. Blue (Cost £30)
£20 Prov sold to Cullenmin
Still available:-
Spare 2.0 CDB on standard bores. £260
Also have the cams from the UK AVCS heads above and a set of 2.5 single AVCS heads in parts if anyone needs anything.
Gutted to be doing this and likely to lose a fortune but such is life.
All prices are + postage or collection from Aberdeen.
I'm willing to meet where possible or have parts passed on as long as they are paid for first.
If using paypal please cover fee's.
The engine was assembled into a Long block and timed up by Steven Darley.
It was never run or even fitted since I collected it earlier this year from Steven's but is now split to try and get everything sold on.
2.1 Short Engine
EJ20 CDB c/with under piston squirters.
Block was stripped, cleaned and inspected. Machined to take crank. Decked and bored / honed to suit pistons.
Lateral performance 2.1 stroker kit c/with Wiseco pistons, ACL race bearings, brand new Nitrided x-drilled EJ257 crank, all new genuine seals etc.
Refurbished water x-over pipe with new o-rings again from Lateral.
All supplied built from Lateral.
£2,600 Prov sold to Cullenmin
New timing belt kit including all idlers and tensioner (2 piece) and Power Enterprise Kevlar timing belt
£150 Prov sold to Chris Allsop
New Cosworth Billet Timing belt guide (Cost £60)
£40 Prov sold to Cullenmin
Samco hoses from and to the water pump. Blue (Cost £30)
£20 Prov sold to Cullenmin
Still available:-
Spare 2.0 CDB on standard bores. £260
Also have the cams from the UK AVCS heads above and a set of 2.5 single AVCS heads in parts if anyone needs anything.
Last edited by duncatr; 28 November 2014 at 11:48 AM.
#4
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jun 2006
Posts: 887
Likes: 0
Received 0 Likes
on
0 Posts
Drivetrain:-
OS Giken STR2C Twin plate clutch and flywheel. Bought used from Banny but he had fitted new plates not long before selling it to me, loads of life in the plates as a result. £400 without push pull conversion if required. Will fit both 5 and 6-speed.
All plates on both pads look fine and have LOTS of meat left in them. 0.155" (3.937mm)
From what I can find online they are 4mm when new
OS Giken STR2C Twin plate clutch and flywheel. Bought used from Banny but he had fitted new plates not long before selling it to me, loads of life in the plates as a result. £400 without push pull conversion if required. Will fit both 5 and 6-speed.
All plates on both pads look fine and have LOTS of meat left in them. 0.155" (3.937mm)
From what I can find online they are 4mm when new
Last edited by duncatr; 25 November 2014 at 11:00 PM.
Trending Topics
#10
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jun 2006
Posts: 887
Likes: 0
Received 0 Likes
on
0 Posts
Parts are for sale on other forums. (Has been for sale on local forum for about a week - hense lots of missing bits and parts prov. sold). Where possible I will work on a first to put their name to something gets it but while I'm willing to hold items I obviously dont want to lose out on a sale so please PM and confirm what you want and when you can pay. I have a sheet to record 1'st and second should any sale fall through then I will contact the 2'nd person to see if they are still interested.