RA Project
#1
RA Project
Well some of you may remember my RA... and all the kind comments you left about it.... On NOT so nice as the case may be...back in 2005
https://www.scoobynet.com/members-ga...monza-wrx.html
Well i took the car off the road last June, and sold bits off... and it never looked like it was going to see the road ever again...
But a couple of months ago i got some inspiration to get it back on the road when i managed to get a cheap 2.5 short block from one of the Snet members...
So i sold my 2.0 forged block, and fitted my STi ported and polished heads.
and have built up my new 2.5 giving it the following spec.
EJ25 Short motor.
STi Ported heads.
STi Std cams.
RCMS Headers
TD06 20G (Not running a BOV)
H&S Decat down pipe and center decat.
Afterburner Vortex Back Box.
Blitz Induction Kit
FSE fuel pressure regulator
Nismo 740cc Injectors
Apexi FMIC
Once this is run in i will be having a Simtek ECU fitted with antilag and launch control.
so now the engine is out the way... it was time to Start on the bodywork....
as you will see from all the pics i have done the work myself, and it is a total transformation....
I have hundreds of pics of the work at various stages... so i will not put them all up... Just a few of them...
Now the Finished Article
the finish is like Glass.
Has taken nearly 3 weeks to do the Bodywork.
https://www.scoobynet.com/members-ga...monza-wrx.html
Well i took the car off the road last June, and sold bits off... and it never looked like it was going to see the road ever again...
But a couple of months ago i got some inspiration to get it back on the road when i managed to get a cheap 2.5 short block from one of the Snet members...
So i sold my 2.0 forged block, and fitted my STi ported and polished heads.
and have built up my new 2.5 giving it the following spec.
EJ25 Short motor.
STi Ported heads.
STi Std cams.
RCMS Headers
TD06 20G (Not running a BOV)
H&S Decat down pipe and center decat.
Afterburner Vortex Back Box.
Blitz Induction Kit
FSE fuel pressure regulator
Nismo 740cc Injectors
Apexi FMIC
Once this is run in i will be having a Simtek ECU fitted with antilag and launch control.
so now the engine is out the way... it was time to Start on the bodywork....
as you will see from all the pics i have done the work myself, and it is a total transformation....
I have hundreds of pics of the work at various stages... so i will not put them all up... Just a few of them...
Now the Finished Article
the finish is like Glass.
Has taken nearly 3 weeks to do the Bodywork.
#2
Scooby Regular
Join Date: Aug 2005
Location: My turbo blows, air lots of it!!
Posts: 9,073
Likes: 0
Received 0 Likes
on
0 Posts
ouch, a **** load of work gone into that then! looking minted now
good choice with the simtek, ive been running one for a while now
remember and post up how you get on with the remap etc
good choice with the simtek, ive been running one for a while now
remember and post up how you get on with the remap etc
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
Phil3822
General Technical
0
30 September 2015 06:29 PM