2.0 Forged Closed deck engine
17 May 2010, 11:32 AM
#1
Scooby Regular
Thread Starter
Join Date: May 2010
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
2.0 Forged Closed deck engine
I have forsale a 2.0 forged closed deck engine. Spent over 5k getting engine together.
Spec.
Closed Deck block Oil squirters lowered to allow higher skirt postons to be used. A block mod was also carried out to allow use of V5 Crank. all done by scoobyclinic.
V5 STI crank crossdrilled and Nitrided for beller oil pickup and stre strength.
Mahle power pack pistons
Manley rods
Cometic headgaskets
STI V4 Heads ported and flowed, valve seats and valve guides reangles by Sholar engineering.
Engine will be able to run 500bhp +
Problems
When i went to change the injectors over, one of the seals didnt seat properly so engine hydrolocked. Havent investigated this further. Could have caused damage to rod piston or valves. Only one cylinder was effected by this. Hence price i want for the engine, need to make space in garage and havent time to investigate. Have a set of cometic gaskets that will give with the engine they cost over £100
I want £1700 for it
Spec.
Closed Deck block Oil squirters lowered to allow higher skirt postons to be used. A block mod was also carried out to allow use of V5 Crank. all done by scoobyclinic.
V5 STI crank crossdrilled and Nitrided for beller oil pickup and stre strength.
Mahle power pack pistons
Manley rods
Cometic headgaskets
STI V4 Heads ported and flowed, valve seats and valve guides reangles by Sholar engineering.
Engine will be able to run 500bhp +
Problems
When i went to change the injectors over, one of the seals didnt seat properly so engine hydrolocked. Havent investigated this further. Could have caused damage to rod piston or valves. Only one cylinder was effected by this. Hence price i want for the engine, need to make space in garage and havent time to investigate. Have a set of cometic gaskets that will give with the engine they cost over £100
I want £1700 for it
engine
18 May 2010, 10:28 PM
#3
Scooby Regular
Thread Starter
Join Date: May 2010
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
I do have the reciepts somewhere i will have to find them. For just the block mods and Scoobyclinic building up the bottom end with the Crank pistons and rods i provided cost £1700.
Will take some pics.
Will take some pics.
Trending Topics
28 May 2010, 07:01 PM
#11
Scooby Newbie
Join Date: May 2010
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
I would also be interested, I take this will fit nicely into a version 3 sti? I gather from what you say this engine has not even been run in yet. More info would be appreciated. What car did it come out of? Will It run ok hooked up to a standard system? Cheers
02 June 2010, 10:24 PM
#12
Scooby Regular
Thread Starter
Join Date: May 2010
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
Here are some pics. There is no cambelt, tensioner, idlers or oil pump on it. There is a pic of the headgaskets that will come with it and a reciept for the bottom end build.
Thread
Thread Starter
Forum
Replies
Last Post
bluebullet29
General Technical
9
05 October 2015 02:17 PM
