ScoobyNet.com - Subaru Enthusiast Forum

ScoobyNet.com - Subaru Enthusiast Forum (https://www.scoobynet.com/)
-   Engine Management and ECU Remapping (https://www.scoobynet.com/engine-management-and-ecu-remapping-453/)
-   -   Can open source maps do what ecutek racerom does (https://www.scoobynet.com/engine-management-and-ecu-remapping-453/975993-can-open-source-maps-do-what-ecutek-racerom-does.html)

stevemoir 28 May 2013 11:43 AM

Can open source maps do what ecutek racerom does
 
Hey folks just wondering about this

So of you may know I used to have a blob with s syvecs

But now I have a hawkeye and I'm wanting a remap

Can an open source map give you the same features as a ecutek racerom map can?

Steve

dan-lincs 28 May 2013 08:06 PM

Can you list the features you would like to have?

bluenose172 28 May 2013 08:48 PM

Some of the features are available, not all though. As above what exactly are you looking for?

bustaMOVEs 28 May 2013 08:54 PM

With a newage Opensource map, (race rom) can get, lc, al, ffs, twin maps etc

The Pink Ninja 28 May 2013 09:17 PM

As above you can run mafless too with carberry but not sure on the , Auto blip(on downshift) and in-gear boost...But could be possible.

bluenose172 28 May 2013 09:20 PM

Carberry is a 16 bit ROM, his car is 32 bit.

The Pink Ninja 28 May 2013 09:31 PM


Originally Posted by bluenose172 (Post 11103431)
Carberry is a 16 bit ROM, his car is 32 bit.

Saw the word Blob and it all went pear shaped after that :D

dan-lincs 28 May 2013 10:24 PM

There is a 32bit SD rom aswell

bluenose172 28 May 2013 10:48 PM

US only isn't it? Must admit I don't take much to do with the 32 bit developments.

07STIhawkeyeAffy 29 May 2013 08:14 PM

Have a sti 2007 can you go maffless on opensource

dynamix 08 June 2013 08:33 AM

no you cant affy - sorry. Just buy a new maf ;)

There really isnt any need to go mafless until well over 450 bhp on the hawk and the current obsession for running mafless is a little weird imo. The std ecu is perfectly fine to 500+ (I ran mine to 540bhp) before it starts fighting you a little more than it should be. Rather than trying to get the std ecu that was designed to do a certain job very well by subaru to do a completely different job using code that isnt 100% tested IMO, best bet is to get a proper ecu such as syvecs to run it after that level.

MartynJ 08 June 2013 10:21 AM


Originally Posted by dynamix (Post 11113856)
no you cant affy - sorry. Just buy a new maf ;)

There really isnt any need to go mafless until well over 450 bhp on the hawk and the current obsession for running mafless is a little weird imo. The std ecu is perfectly fine to 500+ (I ran mine to 540bhp) before it starts fighting you a little more than it should be. Rather than trying to get the std ecu that was designed to do a certain job very well by subaru to do a completely different job using code that isnt 100% tested IMO, best bet is to get a proper ecu such as syvecs to run it after that level.

Whilst I agree with what you have said below, you can go SD on 32 bit ecus on opensource or Ecutek should you want to :D

http://www.romraider.com/forum/viewforum.php?f=37


All times are GMT +1. The time now is 03:42 PM.


© 2024 MH Sub I, LLC dba Internet Brands