Is worth the risk ? Remapping.....
 

Currently own a 95 wrx, with various mods/improvements etc, if i were to remap i would fit a front mount as well as a cone filter into the wing to totally utilise the remap etc, anyway, with my mods and the front mount id expect to see around 300 bhp etc, torque im not sure about, but its that what i want, not top end power, but the grunt getting there.

So, with 98k (miles) on the clock, is it worth the risk, for say, a gain of what, 40ish bhp ?!?! im guestimating my bhp to be about 260 with the z4 ecu as with age, power drops a bit etc.

So, even tho ive owned it 8 yrs, it was an everyday car, now more a short journey/weekend car,
oil changes every 5k and always well maintained, is it a gamble waiting for those big ends to pop at 98k on the rollers ?

cheers

Not worth the risk, leave it as it is! It'll go bang if u up the bhp anymore.

why will it????

i'm running 320bhp and 101k on the clock

All cars vary, yours maybe ok his may go bang! That's the question, is it worth the risk?

I would think of it this way...could you afford the engine rebuild (standard or forged) after you've spent the money on the mods if it does go pop?

Mate of mine had his bug Wrx mapped on 105k, hasn't skipped a beat yet and it's now on 120k!

iguess its just pot luck then really LOL, ive always ran it on shell optimax/vpower and used decent oil etc, so i guess theres only one way to find out LOL,but as others have said, i couldnt afford the rebuild so for the sake of some better torque/bhp i might have a dead car, hmmmm


cheers

You will have to change the ECU first. Unless its been done already?

yeah,realise that bud :thumb:

It may do the car a favour and prolong its life. And may get it running more efficient and with less stress.

Do it, just don't take the pis5 with the boost you run for the sake of your gear box :)

no hard arse launches and she,l be fine im at over 300 for years with no probs (apart from bloody gearboxes!)

I've recently asked myself the same question with my Blob WRX Wagon PPP, she's on 94k and runs like a dream.

I could spend a grand and see circa 320/330bhp and slightly better mpg but are the gains worth the risk, i even have another built bottom end sat in the garage and spare block, pistons and rods and i can do it all bar the mapping myself, but i just can't be ar$ed with the hassle if it all goes pop, been there done that.

So i decided to leave it as is because in reality it does everything i need it to for road use and on the basis of "if it aint broke don't fix it" :thumb:

Because you've changed the oil every 5k your big ends are probably in better condition than a 50k mile car that's not been looked after as well.

I'd go for it, sounds like you look after the car.

Change it ???
Why, ESL works with his model year.

If anything it will be safer after a mapping session.
Get it done !!!!

The gearbox and engine should be easily able to cope with 300bhp.
If it's a 16g you should be able to get 320-330 out of her with little problem.
You could also consider fitting an STI top mount from one of the newage models if you want the car to remain a little more responsive. If you're not going all out power then you will likely find that a better combination.

Contrary to popular belief you don't always need a FMIC unless you're aiming for power in the late 300's.

my classic had done 120,000 miles when i had it remapped now its at 136,000 and still ok and running about 320bhp

I've just read about a chap replacing the ECU with a PPP over a standard with no map. Is this possible and how safe is this?

Pointless unless you had all the extras that the ppp comes with. And in my opinion a custom map to suit YOUR car is far far better. The PPP map is just a generic one, a custom one is programmed around your specific car.

A custom re-map sounds great, but when you look at the cost and factor in a motor with 100k on the clock. A straight ECU swap looks a good route, especially when your not after mad power. Just wondered if anyones had this experience? As the chap who done this claimed to see a big improvement.

Did they do a PPP for classics!?
Even if they did, as already stated, the PPP maps are generic and not customised on a per car basis.
As a result, they often don't make the claimed power.
I certainly wouldn't advise it unless you have the exact parts for the PPP from the same year and model, and even then I'd still go for a proper remap because it's just not worth the risk - you just don't know what you're getting on the ECU.

Get an ESL board fitted and have it mapped properly.
These are not cars you can scrimp and save on if you want them to run well, end of unfortunately.

I fitted a ScoobyECU to my MY93 WRX a number of years back, which upped the boost (TD05) from about 0.7 bar to around 0.95 bar. The change from the original map (can't remember vintage, but isn't a Z4 ECU) was fantastic - earlier spool-up and consistent pull all the way to the red line.
My car has limited mods - decat exhaust, but still running a standard air box and slanty top mount. Not sure on the current power, but the engine has well over 200,000 miles on the clock. So long as the engine is looked after, a mild remap shouldn't make too much difference - if you think of the percentage of driving time that you actually make use of the extra power / torque, it will probably be minimal.

Don't agree I'm afraid.
If you add mods to the car without a map going in too it can result in the car running rich or lean, fuel cut and all sorts of other problems, some mild, some obviously major but none of which you really want with a performance car.

The majority of people who live by the "my car runs fine" motto tend to find 6 months down the line the car develops rather worrying rattles in the engine bay.
A member of our group took the "won't bother with a map" route and swapped his ECU, then drove it around on full boost.
The car overboosted, there was det, and a few weeks later the engine sounded like a bag of spanners and he was posting asking what might be wrong.

Even a decat vs cat pipe makes a difference to how the car works and the ECU's can only adapt so much, especially the earlier ones.

When I first got her, my old WRX on a TD04 made 208bhp on the standard map with a centre section and backbox fitted, and then 248bhp after mapping on the rollers. I'd say 40bhp is a substantial increase and I was confident I could push the car to its full capability because it had been mapped with safety margins in mind.

If you don't map it, you have no idea what the ECU is doing, how much it may retard your car, and how much it can reign in the engine when it's unaware of the changes that have been made.
And that's why every time someone who says "my car's running strange / misfiring / behaving erratically / sounds odd" I ask "has it been mapped?"
If they answer no, I move on to the next thread....

It's a simple equation in my eyes. Do I spend £300 on a map or £2000 on a replacement engine?