Leaking rear lights on classic
Hi I hav changed my rear lights on my wrx classic from Lexus back 2 standard there was sum black dum dum sealer on the lights I also added some rtv sealer on an they r leaking I hav been told its common 4 the rear lights seals 2 leak has any1 experienced this n wot is the best stuff 2 use? Thanks
|
It's very common, I used a black silcone from halfords I had, I know it's not the best, it's fixed the issue but I know if I want to remove the lights it is going to be a pain, there is a load of threads on here, with the right product to use, it's a non setting Sealent
|
When I got my car it had L.E.D rear lights, I also went back 2 standard, Best thing I could say is clean off any old sealer etc and use some tiger seal to put the new ones in, and you should be ok, I aint had no leaks since.
|
Thanks 4 the advise is tiger seal like a silicone sealer that goes off (sets) on the standard lights I put in there was sum kind of sealer on then like play dough u could mould
|
For God's sake DO NOT use Tiger Seal, Sika-Flex, or silicone. It will seal them, OK, but you will never get them off again...what happens when some idiot in a supermarket carpark busts one for you???
The correct stuff to use is this:http://www.ebay.co.uk/sch/i.html?_tr...at=0&_from=R40 It's a non=setting mastic. Clean off all the old stuff from lights and car: old screwdriver, lolly stick, white spirit and patience. Squeeze a 10mm bead of Carafax around the light, and press firmly into place, replace all nuts. Job's a good'un, and the light CAN be removed when/if necessary. NB: you might need to buy a sealant gun suitable for 400 ml cartridges, Screwfix, Wickes etc. The usual ones are for 350ml. |
Originally Posted by Ryan Hawkins
(Post 10919574)
Thanks 4 the advise is tiger seal like a silicone sealer that goes off (sets) on the standard lights I put in there was sum kind of sealer on then like play dough u could mould
But alcazar has a good option you should go for that :) |
Did u put the carafax around the studs on the light units?
|
Originally Posted by alcazar
(Post 10919829)
For God's sake DO NOT use Tiger Seal, Sika-Flex, or silicone. It will seal them, OK, but you will never get them off again...what happens when some idiot in a supermarket carpark busts one for you???
The correct stuff to use is this:http://www.ebay.co.uk/sch/i.html?_tr...at=0&_from=R40 It's a non=setting mastic. Clean off all the old stuff from lights and car: old screwdriver, lolly stick, white spirit and patience. Squeeze a 10mm bead of Carafax around the light, and press firmly into place, replace all nuts. Job's a good'un, and the light CAN be removed when/if necessary. NB: you might need to buy a sealant gun suitable for 400 ml cartridges, Screwfix, Wickes etc. The usual ones are for 350ml. |
Wot about the studs on the lights? I'm guna order myself a tube of carafax 2moro : )
|
just put some plumbers mate on them! it never sets hards so its :thumb: up if works lol might try that on mine, but i think mine is leaking threw the spoiler to
|
Plumber's mate is similar to Carafax, but tends to produce a non-sticky surface after a time. It also comes in a tin and is messier to apply;)
Carafax is MADE for bedding stuff like awning rails onto caravans. It won't go hard, it won't set, it remains sticky, you can remove and refit the lights at will. I didn't put any round the studs, just on the bit where the light meets the bodywork, which is clearly defined on the rear of the light unit. Not had any problems. It wouldn't hurt to put a thin circle around each hole on the outside, before seating the lights. |
All times are GMT +1. The time now is 09:34 PM. |
© 2024 MH Sub I, LLC dba Internet Brands