Wanna smaller front numberplate
 

Got a 2006 Hawkeye. It has a conventional UK front numberplate. Looking at the shape of the bumper behind it I believe it lends itself to a squarer one. I want to stay legal so what size should I go for? Any pics of yours guys?

I'm interested in this too for my Blob, the standard UK size seems to overhang the bracket and looks a bit floppy...

I want to keep legal though!

+1

I have had a small one on for about a year now on the front, never been pulled and done many thousands of miles, will keep it on there until I am! Looks much better then a massive one on the front, only a matter of time before they get you though

Attachment 57171

What's the size of that mate?

I have the same size in my classic and never had an issue

good question, i will have to check, think its either 9" x 3" or 12" x 3"

Fancy plates.com
3/4 size plate you want

Attachment 57165

If you have standard letters and spacing you only need 11mm around the outside to be legal. So particularly if you have a plate with less characters on it you could shorten it by quite a lot, and also you can probably take 3 or 4 mm off top and bottom, from my measurements, which might just help enough with aesthetics :D

http://img.photobucket.com/albums/v7...ps6a2b55b0.jpg

9x3 for sure

I had one on my06 hawkeye and after a year been pulled over and got ticket for that + had to go to mot station - that's extra cost few quid . not worth it - that's my opinion

Got a 12" x 3" on mine. No bother from PC plod as yet. I'll post a pick when I get back in later if you like.

Want it to be legal and as I have 7 characters there is not much to be gained by shortening the conventional one. any pics of 4 characters on the top and 3 underneath like the 4x4 ones? (11x8) Also is there a smaller import one? and is it legal?

I've been stop twice in a year...got away with it the 1st time just got advised to change it.,2nd time was made to change it.

Standard Jap Import plate

Attachment 57166

Pic of mine

Attachment 57174

Took it to the cop shop before fitting it to ask a traffic cop if it was legal, his reply was YES although " depends on the copper pulling you" :cuckoo:

Martin

Here's mine:
Attachment 57172
Its a standard 4x4 size i think. I had an even smaller plate at first, but the missus was pulled and fined £60, so had to fit a legal size.

12 x 3 ;)

Attachment 57162

very nice but not legal !!!
 

very nice but not legal !

I have a standard UK square plate on my hawkeye, will try and get pictures uploaded.

It is a 100% legal UK size.

Halfords actually do a shorter plate. The height is the standard size but the length is shorter and it`s 100% legal.

The tiny plates on Blobs, which are actually shorter than the mounting point look ridiculous IMO.

illegal size,font and spacing :thumb:

http://i890.photobucket.com/albums/a...821_184600.jpg

Just get a five digit plate and keep it legal

Attachment 57163

mine is classed as an american import plate and has the bs number on it

Attachment 57175

Standard lettering, got it from fancy plates and asked for a 10mm border all the way around :)

Attachment 57164

I'm having mine made by dvla....
Jap imports that have no place for a "normal" oblong plate
Can use smaller fonts.!!!!!
http://www.sandhurstautoprint.co.uk/...age-three.html....

Motorbike plate on mine.

Attachment 57167

From Halfords, won't sell you one with a UK car though.

Jap imports do have space for a standard UK plate. ;)

But do i remember imports can run a smaller plate/lettering?

If so what size?

Only If fitting a uk plate will affect the vehicles ability, blocking a fmic is not an excuse, I have a similar to the blue classic above, would say its slightly under 3/4 size , looks much better and no issues with the police.

Can't remember the size of my plate Andy, although you can see the size difference in this pic.

The larger one is the standard import sized plate that most get.

Attachment 57168