whos got a scoobyclinic turbo?
 

just a thread to see who has a scoobyclinic sc turbo and what power you have managed to extract from these epic turbos.please state which turbos,what car and what mods :)

sc46 billet
p1
2.0 forged,syvecs,6 speed,fmic,flowed injectors,tubulars,fuel reg,3" vortex straight through,600bhp walbro,scoobyclinic bespoke caik.
mapped with 20% math by scoobyclinic
506.9 bhp :luxhello:

i have an sc46 billet, but its still in a box in my garage

what engine do you have pal?

i have a blob sti 2.0

got the sc46,matched upipe,hybrid fmic, h and s 3.0 decat exhaust,tubular headers,walbro 255,fpr.reworked lateral injectors


all going on the car shortly.

going to be mapped with syvecs and running 20%meth doubt it will be anywhere near you bhp

shouldnt be far off pal.great spec there.my mate has similar spec and has 450+ and its epic on the road :)

taking the car off the road in the next few weeks to fit it all then i will have it mapped and rr it.

I also have a sc 46 billet on a 2.0 forged cross drooled nitrated crank lateral800 injectors Walbro 255 pump fmic reversed inlet and flipped inter cooler for shorter pipe less lag work 3inch system all the way thru 6speed conversion fuel reg parallel fuel lines braided fuel lines aps air inductin kit located in wing equal length headers and running on Simtec well alkatek not running yet it's nearly finished couple of weeks.. Then a running in map then full map going with straight vpower first then if not happy with that 20% meth so don't know what power it will be yet but should be fun in a classic !

sc
 

i have a 2lt blob running sc 40 turbo standard intermals,fmic, 1000cc injectors,walbro,3" turbo back,k&n induction,ecutek by jgm,running 420hp with 20% meth

Great figures from the sc40 mate.i bet spool is emmense :)

i love it mate but its time for upgrade but not sure on what turbo yet,worried about lag

i had a billet 20g pal but my sc46 kills it and for a biggish turbo isnt too laggy.my mate has an sc42 and that spools amazingly and makes great bhp too.win win :)

Been advised on sc42 when I get my stroker built at engine tuner so anybody running one and can give some feedback would be good.

My SC38 made 395hp on a 2.0 with std headers and uppipe, Hybrid GT2 FMIC, 550cc injectors and run on V-Power.

wow that is a great figure pal :)

Impressive figure for an SC46 on a 2L. My spec is very similar to yours on an RCM 400, & Iv been thinking of uprating to the SC46. I think this has just made my mind up, hope it's not too laggy.

i think its spot on pal as the power is immense.the ratios of the 6 speed help :)

I have a JDM 6 speed so it should be fine. Did Pat map it?

Gt30billet rotated rcm kit,block is 2.5,stage3 cosworth heads and cams.cosworth billet crank,6speed,vpower made 504bhp,on 1.6 bar boost,,,,it's quick real fun to drive boost is there when u need it:cool:

Yes pat mapped it mate.i love it.the clinic did me proud :)

Sounds fun :) what have you done to the 2.5 block to cope with 500 bhp pal?

GT35 billet 570 @ 1.5bar

What engine banny?

2.35 avcs heads, full thread in project section :thumb:

If you only want 400/400 an sc42 would be better IMHO :)

I have a SC42 fitted on a 2.0 lt which was mapped at scooby clinic and it made 401bhp, 1.45 bar boost, ecutek, quite pleased as I am still on a top mount and a cat in the down pipe, was on pump gas V power.

That's a great result mate :)

That's quite a conservative boost level? With something like 1.6 bar and de-cat that should top 420 I would have thought?
I'm considering an SC42 (currently MD321H) and have a pretty good list of supporting mods so I would be aiming for 420

JohnD

If you have the right mods it should make 420 pal :)

Anyone got a gt30 billet on 2.1 stroker?

Anyone?