UK 6 Speed Gold Brembos etc for sale
 

Hi Guy's,

getting fed up not having a scooby on the road, so i am considering selling off some performance bits, from my RA to get it back on the road.

6 Speed Box from 2004 UK STI, covered 64k when i got it, and done less than 3k since.
Comes with complete classic conversion.
SOLD to Bigals




Front Gold Brembo Callipers, with Brand New Discs and Pads from Aztec Performance. 5x100 pcd

Discs and Pads have not been fitted yet, still in the Box.
[FONT=Arial][SIZE=2][COLOR=Black]Calipers are in good condition, and are not seized etc, after what they cost me with the new Discs and pads.

£650




Set of 4 of CDF Racing Spacers 20mm £75 sold to sandyRS16i payment. Recieved





Cheers
Derek

steve moir is looking for a GT30 mate

standard fit gt30? forgive my ignorance but i didnt know there was 1? what car/engine was it fitted to and what were you going to fit it to? i have an rcm 450

I think he means its a GT30 but it hs a standard fitment rather than twisted etc so it just drops in.

I am looking but it's the wrong time unfortunately :(

Steve

TURBO
 

Does turbo come with water pipe and oil pipe??
What inlet size is it??
Any photos
Regards
Tim

more info on turbo please and pics mate

I will get pics tomorrow, I believe it has the oil and water pipes. I know it has the oil for sure, as the guy sent this on too me a couple of weeks later when he came across it.

And yes i mean it fits in Standard location and is NOT a twisted setup.

As for the inlet i will measure this tomorrow, but from memory i think its 76mm

Having had a GT30 rotated which is a 100MM inlet i thought this turbo was not what i was told when i seen the inlet, so I Gave MartynJ a call and he confirmed the inlet size was correct for the Std location turbo.

Pics of the turbo are now Added.

as my question m8 what engine was this on to make that much power? and what were you going to use it on?

If they are the spacers I sold you mate then there were 2 pairs!!

Free bump

Thanks Screech.

You are correct is is a set of 4 that i got from you. I have updated the thread.

@ Snake. the person i purchased it from told me it was on a 2.1 Stroker that was built by Advanced Automotive, i no longet have his contact info so cannot find out what boost rate.

I was going to run it on a forged 2.0 Not sure if i am going to use the forged engine or a std one i got, hence why it's not up for sale.

I cannot affoard the twin plate clutch i wanted, and the new ECU.
I was also thinking on converting to AVCS heads changing the Dash for a Bug STI dash and use the Bug loom too.

the car has been off the road over 12 months now and it's killing me. I just want it back on the road.

I will just go for around 400 again and use a 5 speed RA box, till it dies again. in the mean time i will save for a JDM 6 speed with DCCD, as i want the low ratio.

Any Interest?

could you put up the graph for the gt30 m8

Sorry, I do no thave this, i do not have alink to the original Advert on Piston heads, and i am sure the pics will be gone now if i did.

I never fitted it.

Bttt

I have a JDM box (non-dccd) might be interested in exchange for the UK box and Diff.

Sounds Good.

P.M Sent

Replied to P.M's Ref Turbo and Gearbox

Up from Page 4

For the record that looks very simulat to the Garrett GT30 with 76mm inlet I had on my 2.0 STI MY02. Made well 413 on TMIC, 3" decat and H&S headers, and then well over this with simular torque on meth with FMIC. It spooled around 3700-4000 which was driveable on the road, and stayed in boost on track shifting through the gears above 7000.

I sold mine for £700 with braided oil feed as cheap deal for a guy that bought an engine from me, and the Samco inlet for £70, Hope this helps, and glwts

www.youtube.com/watch?v=IGQK1f9-9y4

Rob ;)

Hi, interested in the turbo if you still have it? I've got a VF48 which was brand new off Simon golly green monster about 4 months about & hasn't run more than 0.8 bar due to a wiring issue which restricted the engine to 4000rpm. It's a good solid 380-400hp turbo if your interested? Pm me
Thanks

Are the spacers hubcentric and do they come with the bolts & fixings? Cheers

Ok Guy's I am trying to weigh up my options at the min.

I have swap offers for a MD321H and another swap offer on a MD321T, and one for a VF48.

I also have a Swap offer on my Gearbox for a JDM 6 speed.

Problem is if i swap i am no tin any better position, I still need an ECU and a clutch to support the power.


@ SandyRS16i

Yes the spacers are hubcentric and come with the bolts and fixings.

They are the ones in the link below, and that is only 1 set for £141.36. I am selling 2 set's.

http://www.cdfracing.co.uk/product_i...9834b615f885a2

Spacers sold to sandyRS16i pending payment.

I have a mint TD06 20G or a VF35 that could px if any use.

Rob

Any More offers on the 6 Speed setup? Best so far is £1400 :Suspiciou


PM'd u rob

Gearbox and Spacers Now Sold

You've yet to replied to my last, if your not interest thats fine ;)

Bump.

Sorry Rob, thought i did reply to you. Will do so Now.