SBR 2.35 Bugeye Wagon JDM WRX AVCS Project
Hi guys
Few months ago we are decide to go for 2.1 stroker,due our engine suffer with low compression on one piston,later we learn this has been caused damaged Valve seats.OE Recon has been cheaper option(with Forged internals),but we are decide go for SBR 2.1 Stroker with AVCS,from our original plan we are want just safe 400bhp,but later we are want little bit more,at moment car will be run just "safe" 450bhp until we are fit 6-speed(yes we are running 4EAT-Autobox :D ) and Syvecs.. We are almost brought the Syvecs,but at the end we are find Syvecs will be un-compatible with our gearbox(is possible do custom loom,but we ended with OE ECU until 6-speed will be fitted in couple of months along with Syvecs) Everything is now at place and we are waiting just on finishing touches and car will be hopefully finished in couple of days/weeks Every work on our car will be carried or all ready carried Neil@Slowboy Racing:thumb: Here is full spec list Engine: 2.1 SBR JDM WRX with AVCS built and mapped by Neil@Slowboy Racing (Cosworth pistons,SBR Rods,ACL Race Bearing sets:big end and main bearing set,Cosworth baffled sump, 12mm Oil pump and water pump,11mm ARP Headstuds,Cosworth HG,79mm Crankshaft) 650cc PE injectors with Fuel Lab FPR and Billet Fuel Filter SBR Parallel Rails Blouch Dominator 3.0XT-R(here known as SC50) Hard Inlet Pipe Custom FMIC Inlet manifold custom powder coated Powder coated Alternator and Header Tank TGV Delete 255lb Walbro Fuel Pump(Bosch 044 second pump) 3port boost solenoid with Apexi AVC-R(2 boost setting) RCM Big cone Setrab Oil cooler 4EAT Gearbox Mocal Oil cooler 3"HKS Carbon-Ti Cat Back Exhaust with Hayward and Scott downpipe GT-Spec Headers with 3 bolt upipe GT-Spec Cooling panel HKS Billet Oil Cap Blitz Header Tank Cap Silicone hose kit Alloy Radiator OE ECU with switchable maps(Group N ROM/ALS and Open Source Remap) by Slowboy Racing and few other mods Suspension mods: HSD HR Coilovers Front and rear CDF Solid Droplinks Eibach ARB FR 22mm & RR 24mm Hardrace Adjustable Lateral Links Cusco 4point Under Brace FR K-sport 8pots 356mm with Ferodo DS2500 RR K-Sport 6pots 330mm with Ferodo DS2500 HEL braided lines Wheels: Kumho Ecsta 225/40 ZR18(but will be replaced with Federal RS-R 595:D) ROTA G-Force 8.5X18" in Titanium Interior: Sparco ProADV-Driver side Sparco EVO-passenger side 4 Way Switch panel Sabelt 3Point Harness Sparco 310-SP Steering Wheel Works Bell Paddle shifter Shadow gauge set(Oil Temp,Oil pressure,Water Temp and Boost) Carbon Defi Gauge pod ATi steering collumn gauge pod(AEM AFR Gauge wideband) Life-Line Mechanical 2.25Kg Extinguisher Kit Alpine Audio PSi3 ECU Data Monitor Exterior mods: Chargespeed Front bumper with Chargespeed Carbon Ducts JDL rear lip with JDL Sideskirts Hella Supertone Horns Vis racing Fuzion Carbon Bonnet Morette with Hi and Lo HID kits(but currently looking for STi lights) I will upload pictures from build today/tonight For any comment thanks Jura |
Great spec mate, get them pics up :thumb:
If you kuhmos have life left in them I may be interested in buying them. |
Here are few pics parts which we are purchased few month ago
AEM Uego Wideband AFR http://i877.photobucket.com/albums/a...8/DSCI0239.jpg Eibach Anti Roll bar kit http://i877.photobucket.com/albums/a...8/DSCI0227.jpg GT Spec Cooling Panel(sorry for crappy picture) http://i877.photobucket.com/albums/a...8/DSCI0230.jpg Blouch Dominator 3.0XT-R(Billet turbo,here is known as SC50) http://i877.photobucket.com/albums/a...8/DSCI0234.jpg Hella Supertone Horns http://i877.photobucket.com/albums/a...8/DSCI0235.jpg HKS Oil Cap and Blitz Header Tank Cap http://i877.photobucket.com/albums/a...8/DSCI0237.jpg and few days ago arrive CDF Droplink set,really pleased with these http://i877.photobucket.com/albums/a...8/DSCI0224.jpg HSD HR http://i294.photobucket.com/albums/m...a/DSC00697.jpg Sparco SP-310 http://i877.photobucket.com/albums/a...rcoSP310-2.jpg Hardrace Lateral Adjustable link/arms http://i877.photobucket.com/albums/a...rdracearms.jpg |
Originally Posted by martin850
(Post 10061218)
Great spec mate, get them pics up :thumb:
If you kuhmos have life left in them I may be interested in buying them. Yes Kumho have thread i think 7mm or more Jura |
Looking forward to them. Keep me in mind for the tyres mate :thumb:
|
Originally Posted by martin850
(Post 10061249)
Looking forward to them. Keep me in mind for the tyres mate :thumb:
Jura |
We are definitely go for "clean" look,all stickers go down and hopefully JDL Rear lip and Sideskirts will look like this on our wagon
http://www.jdltuning.com/media/catal...w/r/wrx_wt.jpg And here are most recent pictures of engine,no everyone cup of tea,but we are like the black look of engine(there is still fitted silicone inlet pipe) http://i294.photobucket.com/albums/m...a/DSC00676.jpg http://i877.photobucket.com/albums/a...d/DSC00683.jpg http://i877.photobucket.com/albums/a...d/DSC00698.jpg Jura |
Black engine looks good
Andy |
looks lovely Jura, nice spec aswell! will keep an eye on this thread
|
Originally Posted by andy00v7
(Post 10061891)
Black engine looks good
Andy
Originally Posted by barnshaw
(Post 10061970)
looks lovely Jura, nice spec aswell! will keep an eye on this thread
Jura |
Hi Jura.
You missed one big item off your spec list :D I wont say what just in case you are keeping it a secret :thumb: |
Originally Posted by Scooby Hoo?
(Post 10062765)
Hi Jura.
You missed one big item off your spec list :D I wont say what just in case you are keeping it a secret :thumb: Jura |
Looking good, nice to see someone else going for a kit on there scoob.
Nice engine too, thiats going to be my next project once the bodyworks done, if it evers stops raining lol Ricey |
Looking good, you'll have to get it up to the Ace once it's done so we can all have a gander:D
|
Originally Posted by Rice Rocket
(Post 10062967)
Looking good, nice to see someone else going for a kit on there scoob.
Nice engine too, thiats going to be my next project once the bodyworks done, if it evers stops raining lol Ricey My bother choice of bodykit,we are want full Chargespeed,but is not compatible with wagon,bloody tw@ts selling only for Saloons :razz: Again my brother choice of color of engine(he want something different),looking forward see yours too,i've seen just older pics:thumb: Thanks for kind comment :thumb:
Originally Posted by JonMc
(Post 10062977)
Looking good, you'll have to get it up to the Ace once it's done so we can all have a gander:D
Cheers Jon,i will,but at moment we are working these days if its Ace Cafe,maybe in Summer,but until we are busy.. Looking forward to see your choice of your color and finished project/product:thumb: Again thanks for kind comment. Jura |
Gona be a great build with good parts list :)
|
Looks good mate
|
Originally Posted by rickya
(Post 10064359)
Gona be a great build with good parts list :)
Originally Posted by wrx9181
(Post 10065356)
Looks good mate
|
I love seeing big power wagons, not the norm. Love it, well done chap. Keep the pics coming....
|
Originally Posted by MattyB1983
(Post 10066623)
I love seeing big power wagons, not the norm. Love it, well done chap. Keep the pics coming....
Jura |
Here are some pics from build
http://i294.photobucket.com/albums/m...a/DSC00702.jpg http://i294.photobucket.com/albums/m...a/DSC00703.jpg http://i294.photobucket.com/albums/m...a/DSC00704.jpg http://i294.photobucket.com/albums/m...a/DSC00710.jpg http://i294.photobucket.com/albums/m...a/DSC00709.jpg Jura |
nice jura , very nice :thumb:
|
Finally a project thread...nice one Jura :D
|
subscribed :)
|
Originally Posted by trails
(Post 10071938)
Finally a project thread...nice one Jura :D
Thanks finally here i have Project thread:D Jura
Originally Posted by IainMilford
(Post 10072267)
subscribed :)
Jura |
Will be an interesting project to follow, similar to my plans for a 2.1 avcs build, good luck with it :)
|
Originally Posted by IainMilford
(Post 10072410)
Will be an interesting project to follow, similar to my plans for a 2.1 avcs build, good luck with it :)
We are using our JDM WRX block which have all ready have AVCS on inlet side and we are using our OE ECU which support AVCS as well,in future we are thinking Syvecs with 6speed. Jura |
the black engine looks good mate,you have some very nice parts in the build.good look with the rest of the build.:thumb:
|
Originally Posted by bigarf
(Post 10074302)
the black engine looks good mate,you have some very nice parts in the build.good look with the rest of the build.:thumb:
Jura |
this looks like a great build jura, looking forward to seeing progress.
Grant |
All times are GMT +1. The time now is 08:18 AM. |
© 2024 MH Sub I, LLC dba Internet Brands