version 4 forged/gas flowed heads
version 4 forged ported and polished heads for subaru impreza 98 import possibly uk compatable too but not sure. heads consist of ported and polished heads, 3 way angle valve seats, bronze valve guides, 14mm rcm wrc head stud conversion, custom spec ground race cams, vernier pulleys, stainless and inkonol valves, double valve springs, titanium retainers, fully shimed. heads come complete and ready to bolt straight on to 14mm studs. heads where bolted to a forged 2.35cc cdb but that as now sold, the total engine build cost me just over £15,000 and was built by api. im looking for £2500 thanks guys
|
bump
|
bump
|
bump
|
anyone???
|
still have heads and pulleys left guys £2500
|
do they come with cams mate
|
are these heads any good for a 2ltr?
|
Originally Posted by 350bhptype~R
(Post 9720163)
are these heads any good for a 2ltr?
|
pm me when there abit cheaper then as i think there abit overpriced at the moment theres a recession on!!! :-]
|
Originally Posted by 350bhptype~R
(Post 9720923)
pm me when there abit cheaper then as i think there abit overpriced at the moment theres a recession on!!! :-]
|
Why were the head casings so expensive? The problem you will have with these is most of the big power builds are now moving to AVCS equiped heads, especially since the Syvecs can easily control these, which makes even a well specced set of v3/v4 heads harder to value/sell. The 14mm headstud conversion also means they are not a drop in fit. What are the cam profiles.
|
Originally Posted by Arch
(Post 9721192)
Why were the head casings so expensive? The problem you will have with these is most of the big power builds are now moving to AVCS equiped heads, especially since the Syvecs can easily control these, which makes even a well specced set of v3/v4 heads harder to value/sell. The 14mm headstud conversion also means they are not a drop in fit. What are the cam profiles.
|
Originally Posted by stidave78
(Post 9721888)
hi arch, they where new casings from api, people wanting high power builds should be looking into 14mm head stud conversion anyway. why spent thousands on building a engine for the heads to lift off the block under high boost??? im not sure what profile the cams are i would need to speak to dave at api, all i know is they are custom ground race spec cams ;)
|
bump
|
bump
|
Originally Posted by Arch
(Post 9722221)
Agree to some extent ref the head studs if you can get soem info on cam profiles it would be appreciated.
dave, we were told by pat herborn who was involved with them- that they are custom grind from steve geary of SGM tuning. wilder than DH22's which are the current fashion. they were timed at 105 inlet & 110 exhaust. hope this helps arch thanks dave :thumb: |
Hi guys,
I'm interested in these for my rally car build. Its a version 3 type R. @ Arch - you say that these will not be a drop in fit because of the 14mm head stud conversion - what would i have to do to make them fit in that case? @ StiDave - i wrote in your other thread in which you are selling a whole of stuff. Interested in a few other bits too. let me know mate. Rgds, Imran |
Originally Posted by Imran21
(Post 9729843)
Hi guys,
I'm interested in these for my rally car build. Its a version 3 type R. @ Arch - you say that these will not be a drop in fit because of the 14mm head stud conversion - what would i have to do to make them fit in that case? @ StiDave - i wrote in your other thread in which you are selling a whole of stuff. Interested in a few other bits too. let me know mate. Rgds, Imran i replied to your other post fella! :thumb: |
bump
|
bump
|
bump
|
bump
|
bump
|
price drop £2300 ono
|
come on guys, £1500 mega price drop at that!
|
heads
yhpb
|
Originally Posted by bwanaiguana
(Post 9762118)
yhpb
|
Heads
Hi Dave
you have a PM :) |
your pm box is full
|
All times are GMT +1. The time now is 01:48 AM. |
© 2024 MH Sub I, LLC dba Internet Brands