ScoobyNet.com - Subaru Enthusiast Forum

ScoobyNet.com - Subaru Enthusiast Forum (https://www.scoobynet.com/)
-   ScoobyNet General (https://www.scoobynet.com/scoobynet-general-1/)
-   -   Just fitted new spoiler and brake light full of condensation (https://www.scoobynet.com/scoobynet-general-1/823246-just-fitted-new-spoiler-and-brake-light-full-of-condensation.html)

Norman Dog 21 March 2010 06:34 PM

Just fitted new spoiler and brake light full of condensation
 
Yesterday got my new STi 8 spoiler fitted which was purchased from a well known supplier on here (not a cheap ebay special)

The quality of the unpainted item was not fantastic, as the guy from the body shop where I took it pointed out. I wasn't really expecting an OEM quality item for the money so I told him to do his best and paint and fit it. Cost me an additional £50 for the extra prep work required.

Picked the car up yesterday morning and as it was raining pretty much all day didn't have the chance to have a good look at the fitted item.

http://i141.photobucket.com/albums/r...IMG_1091-1.jpg

Went out to clean the car today and noticed that the brake light is full of condensation. :mad:

http://i141.photobucket.com/albums/r...m/IMG_1083.jpg


Not a happy chap at all, I am going to email the supplier and ask for a replacement brake light to be sent out today, however I'm pretty sure that this will mean removing and refitting the spoiler to replace the brake light, which I will probably end up having to pay for.

Anyone had similar problems and can give me any advice..:brickwall

djwrx 21 March 2010 06:41 PM

yer i think mine has got a tiny bit in.think you going get in this weather.tis a pain if you wanna remove it taking spoiler off etc.i had couple leaks on mine from the cable that secures it to the boot..cue loads silicone.hope it dont course you problems,,it shouldnt should it??think the leds will be sealeed it probaly just on the outer cover

The Zohan 21 March 2010 07:01 PM

you car looks great, black wheels a nice touch.

take the light unit out, clean and dry it then some clear sillicone sealant will do the trick:)

scoobzal 21 March 2010 07:06 PM

looking good mate

djwrx 21 March 2010 07:07 PM

i would consult whoever sold it you..if you going start taking spoiler off again etc you may as well get a replacement.if it same make as mine the wire is connected to original loom and i think would be pain in ass job.plus if it was new the unit should have been dry anyhow.personaly im going live with the tiny bit i got on mine.it dry in the warmer weather and doesnt affect the lights itslef

TurboAndy 21 March 2010 07:22 PM

Its an easy enough job to remove but you could do with some one to help you but you can get away with doing it your self.

A number of bolts to remove and unplug the brake light which should be on your tailgate hinge.

Hope this helps.

alcazar 21 March 2010 10:13 PM

That looks like a typical aftermarket light, held in with two screws. You ought to be able to undo the screws, and pull it out, after undoing the connector near the hinge.
BUT: you need to drag a bit of rope/string/wire through after it and leave that in place in order to refit the light.
To dry it, place it with any holes uppermost in an airing cupboard, on top of the boiler etc for about 24 hours.

If you want to be sure of no condensation, place it in the freezer for another 24 hours before refitting. No I'm NOT joking: driest place in the house;)

daz1968 21 March 2010 11:48 PM

I had same problem with mine, tried drying it out with heat, also re sealed with silicon, still couldn't get it to seal, however the supplier has sent me a new brake light foc, so can't really complain, after looking at the new one, I am going to change the grommet for one with a better fit and still use clear silicon on it, hopefully that should stop it.

Norman Dog 22 March 2010 08:19 AM


Originally Posted by alcazar (Post 9300519)
That looks like a typical aftermarket light, held in with two screws. You ought to be able to undo the screws, and pull it out, after undoing the connector near the hinge.
BUT: you need to drag a bit of rope/string/wire through after it and leave that in place in order to refit the light.
;)

I think I will give them a ring and see if they will provide a replacement brake light, it is the type with the 2 screws in so shouldn't be that hard to replace myself.

If the supplier doesn't wasnt to know, it's name and shame time...
I certainly don't expect that kind of problem with something brand new. :mad:

rookymatt 22 March 2010 10:06 AM

I have this problem too, sealed it with sikoflex and most of the condensation is gone. The problem is the units aren't made that well so an ammount of water can get in. Not to mention the x2 screws started to rust now! Went to screw fix and got some stainless screws of the same dimentions! ;)

alcazar 22 March 2010 02:51 PM

LOL, I was going to mention stainless screws, always worth it.
I use Araldite for sealing stuff like this, permanent and easy to use.


All times are GMT +1. The time now is 07:00 PM.


© 2024 MH Sub I, LLC dba Internet Brands