remap results
the day has finally come,just got back from powerstation for my tek 3 tweek. the car got 310.5 bhp on the rollers which im happy with. the car is a my00 with the following mods
tek 3 vf35 turbo ported and wrapped headers greddy up pipe sti8 intercooler intercooler fan large scoop custom undertray and air splitter walbro pump parallel fuel rails ported throttle body inlet manifold insulators hks pannel filter airbox mod with extra cold air feed on the side prf7b spark plugs ic spray set up with 4 nozles 3 inch open neck downpipe (wrapped) decat centre newage prodrive back box. oil catch can theres a bit more lag but the car pulls loads harder now and the turbo sounds quality, its runing 1.25 bar boost and holds up to 6000rpm |
nice results
Ive just had my 2.5 20g mapped by Paul@ Zen. I dont have any power/torque figures, best guess 340*340 at 1.2bar rising to 1.34bar, with a little more to come later! Here is a piccy of hand commander peak values on 1.2bar 5th gear <a href="http://img92.imageshack.us/my.php?im...30610428jl.jpg" target="_blank"><img Andy |
was that on UK heads Andy? 51% injector duty?? what size have you got in there? :p
|
Originally Posted by Neilo
was that on UK heads Andy? 51% injector duty?? what size have you got in there? :p
|
gotcha, what are you hoping for when the "bit more to come" kicks in? Gotta get more out of the 20g surely!!! :D
|
Originally Posted by Neilo
gotcha, what are you hoping for when the "bit more to come" kicks in?
Thanks go to Api for doing this http://img115.imageshack.us/img115/8...01280044bm.jpg Rentonone, sorry Ive hijacked your thread, apologies Andy |
so 6 speed going in soon then
|
Originally Posted by andy97
Im not exactly sure, we did a 1.5bar 5th gear run and it went like a bullet. but Paul advised me to keep the boost down for a short while to preserve the gearbox, but as you can see there is plenty of room to up the settings. 2.5sti with forged pistons on uk 97 heads, car was a standard 97 uk turbo :D
so rentonone, good results mate :) you must be chuffed :) |
rentone..... excellent mate,a good result and around what i thought you might end up with,go and enjoy it now mate.....
|
Originally Posted by andy97
Im not exactly sure, we did a 1.5bar 5th gear run and it went like a bullet. but Paul advised me to keep the boost down for a short while to preserve the gearbox, but as you can see there is plenty of room to up the settings. 2.5sti with forged pistons on uk 97 heads, car was a standard 97 uk turbo :D
Thanks go to Api for doing this http://img115.imageshack.us/img115/8...01280044bm.jpg Rentonone, sorry Ive hijacked your thread, apologies Andy |
Nice results mate.
What was the torque figure? |
Originally Posted by andy97
Im not exactly sure, we did a 1.5bar 5th gear run and it went like a bullet. but Paul advised me to keep the boost down for a short while to preserve the gearbox
|
Originally Posted by rigga
rentone..... excellent mate,a good result and around what i thought you might end up with,go and enjoy it now mate.....
|
james...... back is on the mend,so might be up for crawling around the car pretty soon..... brackets for the newage ic have arrived so thats all sorted,just a matter of bolting all the bits on and get it mapped......
|
Originally Posted by scooby_matt
Nice results mate.
What was the torque figure? also, whats 1.25 bar in psi? thanks |
Originally Posted by rentonone
torque was 371.8 Nm. im not sure how you work it out into lb/ft.
also, whats 1.25 bar in psi? thanks That's about 18 psi AFAIK |
Originally Posted by rigga
james...... back is on the mend,so might be up for crawling around the car pretty soon..... brackets for the newage ic have arrived so thats all sorted,just a matter of bolting all the bits on and get it mapped......
|
James: Told you that scoop was good!
:D Graham |
371.8Nm=274.2lb/ft
1.25bar=18psi |
Originally Posted by scooby_matt
Does that mean you're on the standard uk gearbox?
|
:thumb:
Originally Posted by 911
James: Told you that scoop was good!
:D Graham |
Originally Posted by RoRu
371.8Nm=274.2lb/ft
1.25bar=18psi |
Originally Posted by scooby_matt
That torque figure seems a bit low :Suspiciou
|
Originally Posted by rentonone
do you think? what could be causing that?
|
Originally Posted by scooby_matt
Don't know, I just would've expected to see nearer 300 with your spec
|
It is low. I was at Powerstation recently for a Tek3 MY00, nowhere near as modded and achieved 272bhp / 272lbft?
1.25bar also (as Rich likes to map to). Ninja Sports Cat dp Magnex cat back JR Panel Filter 3 port boost solenoid |
James i would be less worried as to what power the car produces on the rollers.as to what it feels like on the road driving in real world conditions
350 is a great bhp for the guys in the pub as you have already stated its a lot better to drive |
Sounds like there are some good results coming from 2.5's. The additional torque makes such a differance especially pottering around town off boost.
Can't wait till I've finished running mine in and had the final remap:norty: It's an STi3, so it will be interesting to see the differance the heads and cams make over UK versions (all other thinks being equal which the never are:) ). Spread the word, bigger is better, and too much is nearly enough:wonder: |
All times are GMT +1. The time now is 01:54 AM. |
© 2024 MH Sub I, LLC dba Internet Brands