ScoobyNet.com - Subaru Enthusiast Forum

ScoobyNet.com - Subaru Enthusiast Forum (https://www.scoobynet.com/)

- General Technical (https://www.scoobynet.com/general-technical-10/)

- - power predictions (https://www.scoobynet.com/general-technical-10/341650-power-predictions.html)

5cby	04 July 2004 10:49 AM

power predictions

could any1 please tell me wot my car would roughly produce with these mods
full decat(TSL downpipe,magnex centre,magnex backbox)
k+n panel filter
scoobyecu(16.4 psi)

car made 224bhp 200 torque last time on the rollers
that was with just the filter and backbox
its a my94 uk wagon

thx

steve

Neilo

04 July 2004 11:09 AM

260?

Brun	04 July 2004 11:10 AM

249Bhp and 230 torque :)
Just a guess - are you gonna get it on the rollers?

Roojai

04 July 2004 11:30 AM

I would be very interested to know as I have the same car with nearly the same mods except it's a JDM wagon with a TD04 instead of your TD05:

MY94 Wagon
Magnez down pipe and decat centre
STi Back-box
VOS chip (16psi)

I suspect you will have more top end and I will have more low down grunt.

Perhaps 260BHp and 230 ft/lb torque for you
and 250BHp and 240 ft/lb for me

lcheater

04 July 2004 12:07 PM

Quote:

Originally Posted by Roojai

What about bhp/torque for a STANDARD 1992 jap import WRX?

Cheers
Luke

Neilo

04 July 2004 12:10 PM

240bhp/230lbft there or thereabouts for such an early import

lcheater

04 July 2004 12:35 PM

Quote:

Originally Posted by Neilo

240bhp/230lbft there or thereabouts for such an early import

Ok cheers mate

harvey

05 July 2004 04:09 PM

Full 3" exhaust? Anything over 245 bhp and similar torque is a bonus.
Standard 92 WRX around 210-220bhp.

Falkirk.scoob

05 July 2004 04:27 PM

Quote:

Originally Posted by harvey

Full 3" exhaust? Anything over 245 bhp and similar torque is a bonus.
Standard 92 WRX around 210-220bhp.

yah peeps get mixed up with ps and bhp the book does say 240 for a early wrx but this is measured in ps and is acheived with 100 ron juice

5cby	05 July 2004 07:28 PM

my zorst is a tsl 3 inch dp
going into magnex centre and bb
think its 2 and a quarter pipe
wot would you have to do to get near 300 brake out of a uk wagon

steve

Falkirk.scoob

05 July 2004 07:59 PM

Quote:

Originally Posted by 5cby

my zorst is a tsl 3 inch dp
going into magnex centre and bb
think its 2 and a quarter pipe
wot would you have to do to get near 300 brake out of a uk wagon

steve

if its magnex it wil be 2.1/2" (75mm) try some cheating juice 50 shot should do the trick:norty:

Falkirk.scoob

05 July 2004 08:05 PM

im no mechanic but the upping the boost is whats needed but this can be pretty dangerous if precautions arent taken. gueges knocklinc etc and iirc anything over 1.1bar ur going to need a fmic

stevebt

05 July 2004 08:43 PM

Quote:

Originally Posted by Falkirk.scoob

im no mechanic but the upping the boost is whats needed but this can be pretty dangerous if precautions arent taken. gueges knocklinc etc and iirc anything over 1.1bar ur going to need a fmic

i run well over 1.1 bar i only have a TMIC

jonjo

05 July 2004 09:06 PM

94 version 1 STI import

full exhaust with open neck down pipe
255lph fuel pump
apexi air filter
ap organic clutch with l&b flywheel
unknown make of blow off valve

what do you reckon? :)

jonjo

07 July 2004 06:27 PM

Any ideas peeps?

Falkirk.scoob

07 July 2004 10:32 PM

Quote:

Originally Posted by jonjo

94 version 1 STI import

full exhaust with open neck down pipe
255lph fuel pump
apexi air filter
ap organic clutch with l&b flywheel
unknown make of blow off valve

what do you reckon? :)

pretty sure your car comes with 250(ps)

standard, u should get 10-15bhp from the downpipe maybe 3bhp from the fw, you do the math:)

dhorwich

07 July 2004 10:54 PM

My MY95 WRX without scoobyECU and has a CAT fitted made 262bhp. Only mods are cat back blitz nur spec exhaust, blitz air filter and dawes set to 13psi.

You should get more than this with the scoobyECU.

Dan:D

All times are GMT +1. The time now is 01:19 AM.