EJ22G (22B) Blocks, new in their boxes!
Anyone interested? Can get my hands on 2 sets!
|
If only I won the lottery!!!
|
Originally Posted by cosbros
(Post 11905473)
Anyone interested? Can get my hands on 2 sets!
Originally Posted by 360ste
(Post 11905761)
If only I won the lottery!!!
|
Share the price, I'm intrigued
|
Originally Posted by ossett2k2
(Post 11905765)
Price please?
Doubt they're that expensive ? :wonder: But it would be the rest of the work that would be needed to be done that would put the spending up. |
Originally Posted by 360ste
(Post 11905770)
But it would be the rest of the work that would be needed to be done that would put the spending up.
But some new blocks would be a good starting point and if they're a good price. Then :) |
Originally Posted by ossett2k2
(Post 11905774)
Goes without saying,rebuilds aren't cheap.
But some new blocks would be a good starting point and if they're a good price. Then :) You seen the second hand prices? |
Originally Posted by bustaMOVEs
(Post 11905776)
For a ej22 at today's rate, there's no such thing as a good price.
You seen the second hand prices? But to make a 2.0 into a 2.1 or a 2.5 into a 2.35 or something similar isn't a fortune,certainly not lottery money! Then I would expect a 2.2 not to be to expensive :thumb: End of the day a good solid block can be machined any way you want from the right engineer :) |
Making a 2.35 from a 2.5 block is a bit of work to strengthen the block and then is a piece of string on how far it can be pushed, few have ran fine yes.
But a 2.35 from a ej22 block is definitely the one to have which has its own proven reliability. Hence the price when the op reveals:) |
Be nice to see a price. Ooh I'm a poet.
But seriousness I would like to see how much. |
An EJ22T go between 1k-1400 for a 2nd hand block, I ran my destroked 2.5 block based 2.35 at 2.2 bar and it got used properly and it ran happily. Any suby engine over 550bhp could go at any time regardless of the block its based just for different reasons, nothing is bombproof at this level.
|
Question is then:
Does it cost more than 1k-1.4k to buy&destroke a 2.5? |
Good question Rich. Wasn't your block pinned Banny? It sure made good power. Would an AS closed block take more? Is a 2.5 destroked to 2.35 the same as a 2.2 stroked 2.35 as in power and delivery?
|
Why on earth would you destroke a 2.5? You want all the capacity and stroke length you can't get, hence why it's common to increase the capacity and stroke length of the 2.0 and 2.2.
Don't say to make it Rev either because 100mm bore and 79mm stroke will Rev alright! Andy Forrest can't get his head round this one either. |
Originally Posted by boosted
(Post 11905810)
Why on earth would you destroke a 2.5? You want all the capacity and stroke length you can't get, hence why it's common to increase the capacity and stroke length of the 2.0 and 2.2.
Don't say to make it Rev either because 100mm bore and 79mm stroke will Rev alright! Andy Forrest can't get his head round this one either. |
Originally Posted by banny sti
(Post 11905798)
An EJ22T go between 1k-1400 for a 2nd hand block, I ran my destroked 2.5 block based 2.35 at 2.2 bar and it got used properly and it ran happily. Any suby engine over 550bhp could go at any time regardless of the block its based just for different reasons, nothing is bombproof at this level.
Would of been loads cheaper for him to go for a closed deck 2.5 like mine,,,,there is no replacement for displacement :D |
Originally Posted by domino46
(Post 11905816)
My good friend just had this proven as he had a newly built 2.35 with a closed deck ej22 with all good parts and ended up putting a rod though the block (high 500s) , then had to source another ej22 at the same high cost as the first one to get back to the same spec in a reasonable time frame
Would of been loads cheaper for him to go for a closed deck 2.5 like mine,,,,there is no replacement for displacement :D |
Sorry for the delay guy's, my boss is on hols and I can't get into his email for pics etc!
We are going to advertise these at £2995 delivered in the UK, overseas carriage will be extra. Just so you know, these were £2500 + VAT and carriage from Subaru when they were available from them many moons ago! I will post some pics when I can get them forwarded to me! |
There you go ossett. Bargain for you.
|
Originally Posted by bustaMOVEs
(Post 11906078)
There you go ossett. Bargain for you.
Best start playing the lottery! |
Am tempted to keep them tho, just in case the 2.35 I already have pops ;-)
https://cimg1.ibsrv.net/gimg/www.sco...38e116c539.jpg |
What is the spec of these (e.g. forged pistons from factory?) and what are the correct headers to use?
|
got 3 used virgin ones (never been over sized from OE spec) sat here aswell
|
Originally Posted by Dan_RA
(Post 11906542)
got 3 used virgin ones (never been over sized from OE spec) sat here aswell
|
Originally Posted by fpan
(Post 11906526)
What is the spec of these (e.g. forged pistons from factory?) and what are the correct headers to use?
|
That's robbey 3 k , doubt anyone will be dumb enough on here to buy one of them
|
Originally Posted by RAGGY DOO
(Post 11906835)
That's robbey 3 k , doubt anyone will be dumb enough on here to buy one of them
|
Originally Posted by cosbros
(Post 11906846)
I'm sort of hoping no-one does buy them but as I said above, retail price from Subaru was £2500 plus VAT and shipping and they are still "mint in the box".
|
Originally Posted by 96sti
(Post 11906883)
Why try and sell them on here if you hope no one does buy them. Defeats the whole topic that you started
|
Originally Posted by cosbros
(Post 11906927)
Because they are my bosses blocks, said he wanted them put on forums, facebook, ebay etc. If they don't sell then I have the chance to get the funds together to buy one or both! If I do manage to sell them I get a small drink out of it.
If that's the case I think you should blow 6k on to blocks mate :) |
All times are GMT +1. The time now is 01:41 AM. |
© 2024 MH Sub I, LLC dba Internet Brands