RIIIDAA's Bugeye to Blobeye conversion Bug2Blob
I've recently had mine done, Bugeye to Blobeye conversion that is. Not something you should contemplate doing if you haven't already purchased your Subaru yet as it'll cost £2k easily in parts and labour in the current climate.
That said, I had done exactly that, but I had my reasons, I wanted / needed a SportShift WRX, and they are JDM Imports and rare as the droppings from a rocking horse. So here is how my bug looked before, a rare frontal photograph, because I personally think bugs are ugly. https://dl.dropboxusercontent.com/u/...%2018%2010.jpg https://cimg1.ibsrv.net/gimg/www.sco...46707ceb63.jpg Although thankfully mine had nice JDM HID lamps and IMO the best looking grille surround for a bug (because it looked blob-ish) Ok, so things to buy, first the more obvious front end items:
Less obvious items I found out during the build:
Optional: Twisted teardrop sideskirts Rear bumper Rear tail lights This alone can cost you £2000~ before paint and fitting, and that's when sourcing items from a Subaru breakers. I've read several times that there's a noticable difference between JDM vs UK World Rally blue even though they are the same paint code, but in truth there will be the risk of noticable paint colour variations between panels when you've sourced such items from any other car. Tools you can expect to use:
OK, the build photos, annotated where applicable. From here on in this post, events occur in real time without the benefit of hind sight from anything written above.
Originally Posted by riiidaa
(Post 11507709)
I'm embarking on my bug to blob conversion today, and have questions re: wiring up the headlights.
My WRX is JDM and had HID headlamps (look to be factory fitted) which I wish to sell on if poss Firstly what is this thing for? It appears to be a terminator cap - to be removed if fitting something additional to the car, but what I wonder? https://dl.dropboxusercontent.com/u/...%2055%2014.jpg https://cimg5.ibsrv.net/gimg/www.sco...1938a71bba.jpg Now then, the main issue, there are a few connectors on the loom that don't interface with the blob headlights (also HID, sourced from MB developments), here are the photos highlighting the connector differences, I'd rather not cut the bug headlamp wiring if poss, blob lamp on the left, bug on the right: sidelights and indicators? https://dl.dropboxusercontent.com/u/...%2058%2052.jpg https://cimg4.ibsrv.net/gimg/www.sco...2fdc07bc78.jpg I believe the next pic is from the ballast? https://dl.dropboxusercontent.com/u/...%2059%2031.jpg https://cimg3.ibsrv.net/gimg/www.sco...a27f876144.jpg what are my options? If i cut the needed connectors from the old bug HID lamps. Am I going to struggle to get them again from breakers / dealer without paying out loads ? Urgently need to know how others have gotten over this really. I opted not to chop the wiring from the back of either headlamps (resale value of bug lamps in tact), in the end I decided to buy an engine wiring loom to cannibalise from a breakers that I could actually visit, because I wanted to ensure that I got one with the correct connectors for my Blobeye JDM OEM HID headlamps, this of course meant taking one of said lamps with me. This was done after day one of my build and before day two, because I didn't know before tear down, that the connectors would be different between model years when I chose to buy the HID version of the blob lamps. Effectively replacing like for like, I suspect even if I'd bought the non HID blob lamps they'd also have had different electrical connectors on the back. Moral of this story, ask the breaker if they can supply the loom tails from the engine bay loom that have the matching connectors to the back of the headlamps you buy. Luckily I had access to another car to get too and from work in the interim. Next up, I'll mention two more reasons we had to just get on with what we could on day one, and source another couple of essential less obvious items. The slam panel from a blob is needed (or chargespeed bug 2 blob conversion kit) I had the latter and intended to use it however a member of my regional forums who lives down the road had ordered a new slam panel before deciding he didn't need to use it after all so I gave him what he paid for it when he ordered it from Proven Subaru. The photos show panels and headlamps being offered up and cutting of the headlamp recesses to accommodate the blob lamps etc. https://dl.dropboxusercontent.com/u/...2012-small.jpg https://cimg7.ibsrv.net/gimg/www.sco...3aae64d3a2.jpg https://cimg7.ibsrv.net/gimg/www.sco...cdcb971c37.jpg https://cimg4.ibsrv.net/gimg/www.sco...3c1526798f.jpg https://cimg5.ibsrv.net/gimg/www.sco...cb7bf06f39.jpg https://dl.dropboxusercontent.com/u/...2036-small.jpg https://dl.dropboxusercontent.com/u/...2039-small.jpg https://dl.dropboxusercontent.com/u/...2043-small.jpg Now then the original bug bumper iron is far two wide to accept blob bumper but even if hacked, the beam along it's top does not sit at the right height to allow the clips that fasten the bumper to the beam where you see the holes in the metal above. https://dl.dropboxusercontent.com/u/...2032-small.jpg https://cimg1.ibsrv.net/gimg/www.sco...a55461f93f.jpg After more cutting and grinding https://dl.dropboxusercontent.com/u/...2020-small.jpg https://cimg4.ibsrv.net/gimg/www.sco...b3065d1e6b.jpg How it looked in daylight the day after, with old bumper iron still on, awaiting parts https://dl.dropboxusercontent.com/u/...2030-small.jpg https://cimg1.ibsrv.net/gimg/www.sco...d1209ed165.jpg Needed in addition to a bumper iron then:
Originally Posted by riiidaa
(Post 539943)
needed for bug to blob facelift...
whatever allows you to mount a blob:
https://cimg9.ibsrv.net/gimg/www.sco...c127774071.png https://dl.dropboxusercontent.com/u/...tated_crop.png Other than obviously the correct 2003-05 bumper iron, what else is missing for the top of the bumper and grill to mount too? Secondly Also need one of each of these, they are push in front wing clips for headlamp, 2003-2005 I'm missing one yellow type, one grey/white needed https://dl.dropboxusercontent.com/u/...%2028%2055.jpg https://cimg9.ibsrv.net/gimg/www.sco...216b1ac4dc.jpg https://dl.dropboxusercontent.com/u/...%2030%2052.jpghttps://cimg8.ibsrv.net/gimg/www.sco...1a3be284c8.jpg :doh: Here's the brackets
Originally Posted by Don1952
(Post 539971)
Missing brackets for locating bumper and probably inside fixtures for headlamps are items 9 & 11 here
http://static.opposedforces.com/epc_...1494959005.png and here :D http://opposedforces.com/parts/impre...llustration_2/ A little note about breakers, both on the whole have been very helpful, however they almost never save any fixings / bolts when dismantling, I don't know why they don't at least attempt too, and just tape them to the items they sell, but they don't as a rule in my experience. https://dl.dropboxusercontent.com/u/...2004-small.jpghttps://cimg4.ibsrv.net/gimg/www.sco...667f3a06fe.jpg Day two consisted of mostly cocking about with wiring, modifying brackets and repositioning bonnet catch clasp higher to allow the new bonnet to close without slamming and heavy handedness. After offering up, marking and chopping: https://dl.dropboxusercontent.com/u/...2022-small.jpghttps://cimg3.ibsrv.net/gimg/www.sco...dfa87dc75b.jpg https://cimg0.ibsrv.net/gimg/www.sco...b60052c920.jpg https://cimg2.ibsrv.net/gimg/www.sco...ee615fc4f8.jpg https://dl.dropboxusercontent.com/u/...2020-small.jpg Loom tails from JDM Bug loom we had to cut off from my original loom, these will be sold on with my JDM OEM HID Bug lights to try and prevent the pitfall I experienced... https://dl.dropboxusercontent.com/u/...ails-small.jpghttps://cimg2.ibsrv.net/gimg/www.sco...771394b91b.jpg The new bumper was tinkered with by previous owner for a front mount [FMIC], did a fairly tidy job of it (unlike whoever butchered the bumper belonging to my auto wrx wagon before I acquired that), I'll get some decent ABS mesh for the inside of this as I'm not a fan of front mounts nor Zen grilles. https://dl.dropboxusercontent.com/u/...2036-small.jpg https://cimg5.ibsrv.net/gimg/www.sco...327760a988.jpg Fitted https://dl.dropboxusercontent.com/u/...2006-small.jpg https://cimg5.ibsrv.net/gimg/www.sco...4c0f7eccaa.jpg https://dl.dropboxusercontent.com/u/...1%29-small.jpghttps://cimg7.ibsrv.net/gimg/www.sco...eb0e33a490.jpg https://cimg0.ibsrv.net/gimg/www.sco...0e630331e4.jpg https://dl.dropboxusercontent.com/u/...1%29-small.jpg The above photo is pre any headlamp level alignment. https://dl.dropboxusercontent.com/u/...1-cropped2.jpg https://cimg4.ibsrv.net/gimg/www.sco...95b4a783d2.jpg So then, before and after https://cimg0.ibsrv.net/gimg/www.sco...73f272549b.jpg https://cimg8.ibsrv.net/gimg/www.sco...56058c4dec.jpg https://dl.dropboxusercontent.com/u/.../bug2blob2.jpghttps://dl.dropboxusercontent.com/u/...er-noplate.jpg The rear was done some time ago, comprising of a blob rear bumper and tail lights, was much more straight forward and done with thanks to my friend from Surrey Scoobies, TGovins and my Dad. Reference material: http://opposedforces.com/parts/impre...llustration_2/ https://www.scoobynet.com/projects-4...onversion.html http://www.surreyscoobies.co.uk/foru...d.php?p=539943 https://www.scoobynet.com/full-cars-...or-spares-438/ |
great thread mate, top job too.
well done |
Excellent job. A lot of work involved but end result is great. :thumb:
|
Thank you both :)
|
Top job there mate, looks great :thumb::thumb::thumb:
|
Cracking job mate. Looks loads better! :thumb:
|
Fair play
|
excellent work mate and well payed off
|
:thumb::thumb::D
|
Updated my insurer on these modifications, now to get out and enjoy driving it.
|
Good lad.Top thread.. :thumb:
|
Good thread
|
good write up will help when i do my hawk conversion
|
You need blob mirrors.
|
Looks miles better
|
All times are GMT +1. The time now is 03:16 AM. |
© 2024 MH Sub I, LLC dba Internet Brands