|
2nd brake bleed & brake stopper
What a difference the 2nd brake bleed has made! After initially fitting the front calipers and changing the hoses/pads & discs, then bleeding, the pedal felt very spongy and had long travel. I was convinced there was still a lot of air in the system but decided to leave it a week or so to try and help all the trapped air accumulate so it would be easier to bleed out. I used the Front right, Rear left, Front left, Rear right method and got a lot of air out of the front left and right rear after the second pass. I bleed them a third time just to be sure.
You know straight away on jobs like this if there’s an improvement and just reversing off the drive I could tell there was real improvement, the pedal being nice and firm with about 1/4 travel. Oh, and I've also fitted fog light covers... https://i1270.photobucket.com/albums...psfb80b1d8.jpg Got about 1/2 litre of fluid out in the process. https://i1270.photobucket.com/albums...psab3f5ca6.jpg Painted centres have rounded off nicely https://i1270.photobucket.com/albums...ps0f02e92d.jpg Rear stickers applied https://i1270.photobucket.com/albums...psf2f85cfe.jpg https://i1270.photobucket.com/albums...ps42e2449f.jpg And sealed the caliper paint front and rear to help keeping them clean be that little bit easier https://i1270.photobucket.com/albums...ps7caa3eba.jpg Also manage to get hold of a used, but mint condition CDF brake stopper to help with pedal feel https://i1270.photobucket.com/albums...ps6fb4774a.jpg https://i1270.photobucket.com/albums...ps5278068e.jpg https://i1270.photobucket.com/albums...psb9157072.jpg Need to get some longer bolts for the mounting bracket as I had to leave the rubber isolation grommets off to get the original bolts back in. https://i1270.photobucket.com/albums...psec534add.jpg I fitted the stopper at the same time as bleeding the brakes but left the final clamping bolt off until I'd got used to the firmer pedal then fitted the bolt to see if there was any difference and I would say it's subtle but the pedal feels firmer at the bottom of the travel when you're applying the most pressure, so for £25 off ebay it's worth fitting...every little helps! https://i1270.photobucket.com/albums...ps0ee4295a.jpg https://i1270.photobucket.com/albums...psa418781b.jpg So I'm happy with the brakes now, confidence is restored, so now I can start adding a little more ummff! :D UPDATE Re-fitted the rubber grommets to the brake stopper using longer stainless bolts: https://i1270.photobucket.com/albums...ps7flnmktm.jpg https://i1270.photobucket.com/albums...psijqcrafe.jpg |
Lovely car!
For the record, that is a Tegiwa brake stopper. I have the same unit. |
Nice little bit of blue bling for the engine bay :)
|
Originally Posted by BrownPantsRacing
(Post 11500518)
Lovely car!
For the record, that is a Tegiwa brake stopper. I have the same unit.
Originally Posted by casasteve
(Post 11500536)
Nice little bit of blue bling for the engine bay :)
|
Hey,.
We used to import those brake stopper but due to quality issues we now make ourselves, fresh batch of classic ones picked up this morning,. Quite funny really as Tegiwa bought some of our subaru pulleys to copy a while back, changed the design slightly ... but when advertized made the exact same spelling mistake I did on their advert:thumb: http://i140.photobucket.com/albums/r...ps8eb90f2b.jpg |
Looks like you've done all the hard work on these stoppers and someone else is doing an exact copy (bar the paint finish which looks like some sort of ceramic glaze, very hard wearing BTW) and undercutting you!
All the credit goes to CDF though as I was very impressed with how much work has gone into this bracket, fits perfectly! |
Originally Posted by modrich
(Post 11500568)
Looks like you've done all the hard work on these stoppers and someone else is doing an exact copy (bar the paint finish which looks like some sort of ceramic glaze, very hard wearing BTW) and undercutting you!
All the credit goes to CDF though as I was very impressed with how much work has gone into this bracket, fits perfectly! |
What's a brake stopper and how does it work?:wonder:
|
It braces the master cylinder against the strutt and bulkhead. When you press the brake pedal the extreme forces bend the bulkhead a little and move the master cylinder. This makes the peddle feel spongy as some of the force is absorbed into the chassis. A brake stopper transfers more braking force to the calipers and gets rid of the spongy feel. They do work and you will feel a difference!
|
...took the words right out of my mouth BPR, it's has a similar effect to fitting braided brake hoses that take up any expansion in the standard hoses. Classics need brake stoppers even more so...
|
Got braided lines all round on mine and a brake stopper and it's certainly an improvement over standard!
Anyhow, I'll stop littering your thread with posts now! :D |
Thanks for the info guys :thumb: as ever, car looks great. :luvlove:
|
PPP kit part 1
Well the final piece of the PPP puzzle arrived today, a genuine Prodrive/Subaru non-res centre pipe (I know that the WRX PPP kit didn't include this, it's off an STi, but thought it would be rude not to...) so wasted no time test fitting the scrubber cat delete (complete with original heat shields), centre pipe and backbox together (all genuine Prodrive parts and in superb condition, took me a long time finding all these) to check everything fits nicely. I'm using all stainless nuts & bolts for longevity.
https://i1270.photobucket.com/albums...ps566601c3.jpg After fitting this lot I've got a PPP ecu and transponder ready to install to release a few more BHP... |
Personally I'd go for a custom map in your current ecu to suit your mods and car rather than fitting the one size fits all ppp ecu. Will unlock more power and will probably be safer to get it setup right.
|
...I know, that's the best way forward but that's a whole wad of cash more plus keeping everything genuine Prodrive (albeit retro-fitted) will help rather than hinder come re-sale time, IMO. I know when I was looking for this car I steered clear of anything mapped and really wanted a PPP car.
|
[QUOTE=modrich;11500863]scrubber cat delete (complete with original heat shields)QUOTE]
Coming along nicely mate but what's a scrubber cat delete pipe? I've got an aftermarket wrapped uppipe & downpipe plus pro drive back box. I'm after a deresonated centre pipe next but was going to keep the main cat for mot, so is the above anther word for decat? :thumb: |
The WRX has 3 cats, one before the turbo (up pipe) one after in the down pipe and the 3rd (scrubber) cat is between the down pipe and midpipe. The PPP pack replaces the 3rd cat with a straight through pipe, so yes cat delete as I said above is the same as decat.
try this link for non-res midpipe, I got him down to £60 before getting the Prodrive one http://www.gumtree.com/p/cars-vans-m...ust/1077114376 |
Fair play your doing a lovely job, keep up the good work, credit to you ;)
This will be one lovely wagon when it finnished |
PPP fitted
the wagon's got burble..
Got the PPP bits fitted over the weekend and what a difference! The wagon has gained approx 40bhp and found it's mojo in the process... First thing was to get what remained of the 2x downpipe/scrubber cat bolts removed at my local garage, it took a welding torch to get them out and temporary bolts fitted https://i1270.photobucket.com/albums...ps0d472e8c.jpg https://i1270.photobucket.com/albums...psa8cdabf7.jpg Then to fit the Prodrive Y pipe... https://i1270.photobucket.com/albums...ps67b4f401.jpg Remove old exhaust system in one. Comparison with Prodrive system on left. https://i1270.photobucket.com/albums...ps906f2e0e.jpg Whilst the exhaust was off it makes fitting the Prodrive 5 speed short shift I'd sourced alot more straight forward as the linkage is above the exhaust. I ordered Kartboy front and rear bushes and an uprated UJ (universal joint) from AS Performance to tighten up the slack in the gear change https://i1270.photobucket.com/albums...ps6a3b6791.jpg Stripped and cleaned all the parts and re-assembled everything with rubber grease... https://i1270.photobucket.com/albums...psaa293643.jpg firmer front and rear bushes fitted... https://i1270.photobucket.com/albums...psefe6305e.jpg Short shift ready to go in the car... https://i1270.photobucket.com/albums...psf7a1aeec.jpg Removing the pin to release the UJ proved a pain and in the end decided to leave the UJ in place as even if I'd managed to free the UJ re-fitting would have proof more difficult still. I tested the existing UJ and it felt solid anyway so didn't feel I was losing anything by not fitting it. https://i1270.photobucket.com/albums...psa55d289d.jpg Old mechanism slides out through transmission tunnel... https://i1270.photobucket.com/albums...psbf0c18e5.jpg after completing the gear linkage install the exhaust was a doddle to fit... https://i1270.photobucket.com/albums...psbc65046b.jpg https://i1270.photobucket.com/albums...psd8ddf7de.jpg https://i1270.photobucket.com/albums...ps803ae768.jpg Then onto the PPP ecu I managed to source with immobiliser https://i1270.photobucket.com/albums...pseeaa9ee2.jpg and the all important key transponder chip which I cloned (£14 from carkeyhelp.co.uk) so I could use the spare key also... https://i1270.photobucket.com/albums...ps9d286fbf.jpg Did this little lot over the weekend and I've got to say it's totally changed the character of the car, it now reminds me of my old '93 WRX when I was 21! Oh the memories... The exhaust burble is just right. When I first started it up it sounded a little too loud but as the gaskets sealed with the heat it settled down nicely. I was concerned about droun at motorway speeds due to having removed the centre resonator but there's non, so the Prodrive back box is doing a very good job of releasing the burble but cutting out any intrusive sounds. The gear shift is superb, probably the best short shift I've fitted as they normally require alot more effort and concentration to use. A sign of a good short shift is when changing gear doesn't stand out or detract from the driving and on my first drive I got back and had forgotten it was fitted altogether, if you know what I mean. It's probably reduced the throw by about an inch or two. On the power front, the midrange is much stronger now and has lost that 'restricted' feel that the standard WRX has, the engine feels a lot more 'alive' and responsive now. In my opinion as these Prodrive parts are so reasonable to buy 2nd hand it really is worth doing and saves a packet over a new exhaust and custom remap. I'm a happy chappy:thumb: |
Nice work, its now also the fastest thing on the planet as its effectively a WRX PPP, don't forget this important fact :thumb:
|
alloys/de-rouged/air filter
My all time favourite Impreza with IMHO the best wheels...
https://i1270.photobucket.com/albums...ps9c63f0d1.jpg And look what got dropped off at work, the wagon has it's uses... https://i1270.photobucket.com/albums...ps48a922a8.jpg They are Revolution Millennium 18x7.5s ET48 in near mint condition with a healthy coating of brake dust to protect the paint! There's some minor corosion around the centre caps and one wheel has a minor skuff. All tyres are Avon with plenty of tread. Will spend a bit of time getting these back to prestine condition and get them fitted after the suspension and geo has been done. Also fitted a Pro-R filter, you can hear a little more induction noise now... https://i1270.photobucket.com/albums...ps2e7cb336.jpg And de-rouged the rear fog light by fitting a Euro spec cluster. https://i1270.photobucket.com/albums...ps3055b6a9.jpg You then need to fit a red LED to mimic the fog light lense https://i1270.photobucket.com/albums...ps02bdaaee.jpg https://i1270.photobucket.com/albums...ps47dc36b6.jpg https://i1270.photobucket.com/albums...ps7cdc0561.jpg |
Some nice additions mate car looks very tidy :thumb:
|
I'm liking that. Did you have to replace the rear light cluster or remove a red filter? I'm guessing replaced as you mention euro spec. Any wiring issues or a straight swap?
|
Originally Posted by craigybaby
(Post 11510654)
Some nice additions mate car looks very tidy :thumb:
Originally Posted by casasteve
(Post 11510666)
I'm liking that. Did you have to replace the rear light cluster or remove a red filter? I'm guessing replaced as you mention euro spec. Any wiring issues or a straight swap?
|
PCA Dynamics springs arrived today, getting them fitted nextweek...
http://i1270.photobucket.com/albums/...ps2a24fb20.jpg |
Jealous of the new alloys! Also liking the euro cluster, might have to get one, my drivers side rear has a leak and is full of ****e so would kill two birds with one stone.
|
wheels & suspansion part 1
Spent hours cleaning up the Revolutions. Looks to me like they had never seen a cloth and had only ever been jet washed so there was a thick layer of brake dust coating the inside of the rim/spokes. Took about an hour per wheel and lots of Bilt Hamber wheel cleaner and Tardis tar remover to get the wheels totally squeaky clean again.
One of the Revolution wheels had a slight curb mark so had my paint guy fill and paint the rim. Here’s a pic just after he finished polishing the rim after painting, perfect paint match I think! As it turns out, a virtually perfect match for the Gun Metal paint used by Revolution is Ford Graphite grey (code 9, P2 & 1305C, XSC1305C) so I have some touch-up paint for future stone chips etc. I did contact Revolution for a paint code but was fobbed off saying it was an obsolete BAE paint code that wouldn't mean anything to anyone. https://i1270.photobucket.com/albums...psd6d0df62.jpg I want these wheels to stay pristine so also had the back of all the wheels painted as the paint was very thin and this is where corrosion normally starts and spreads under the paint to the front of the wheel. https://i1270.photobucket.com/albums...ps44834cee.jpg There was some minor corrosion starting behind the centre caps so cleaned and etch primed all 4 centers to be safe and also cleaned and treated the steel wheel nut inserts as they were also corroding. https://i1270.photobucket.com/albums...ps9a8e85c0.jpg Used the Ford Graphite grey to finish https://i1270.photobucket.com/albums...ps5f459d78.jpg Sealed with the wheel faces with Finishkare FK 1000 but left the inside unsealed until the wheels are balanced so the wheel weights stick properly. https://i1270.photobucket.com/albums...ps1cec993b.jpg So next up was to get the suspension sorted. Order new KYB front struts (rears are only 6 months old) https://i1270.photobucket.com/albums...ps987a5a74.jpg new front top mounts https://i1270.photobucket.com/albums...ps6e49cac3.jpg front and rear bump stops and rear strut spacers for the non-inverted dampers (don't know what spacers are on there at the moment, but these are just in case). https://i1270.photobucket.com/albums...pse80410a2.jpg And the all important PCA Dynamics (Prodrive) springs... https://i1270.photobucket.com/albums...ps2a24fb20.jpg This lot is being fitted today so should have some pics of the wagon transformed very soon. Can't wait. |
Popped up to the garage at lunch to seal the inside of the wheels now they've been balanced...
https://i1270.photobucket.com/albums...ps7f4d80dc.jpg Wagon was up on the ramp https://i1270.photobucket.com/albums...ps60e362f9.jpg having the first strut fitted... https://i1270.photobucket.com/albums...psaed3503f.jpg those callipers need cleaning already.... |
Looking good. Are you anticipating that the new struts/springs will make it sit much lower?
|
I'm expecting the rear to drop circa 10mm and the front to drop around 25mm to give a level front to rear stance, where as at the moment the front sits a lot higher.
You fitted yours yet? |
| All times are GMT +1. The time now is 06:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands