defi help please. please please
Guest
Posts: n/a
defi help please. please please
hi all. im looking at getting a set of defi bf guages for my 04 sti. boost, oil temp and oil press. so i will need the following................:-
3x guages
1x triple center pod
1x defi control unit
1x sandwich
but what i need to know is,....................do i need anything else ? do the guages come with the wires/sensor whatever it maybe to reach the sandwich? these would be quite long?
dan
3x guages
1x triple center pod
1x defi control unit
1x sandwich
but what i need to know is,....................do i need anything else ? do the guages come with the wires/sensor whatever it maybe to reach the sandwich? these would be quite long?
dan
Why do you want to use a sandwich plate??? yes the defis come with all sensors and wiring.The best place to fit the senders is under the intercooler above number 3 cylinder (adaptor available to replace blanking screw thats there at the moment) Oil pressure fits under the alternator in place of existing sender and the boost runs off the Dumpvalve vacuum pipe
LOL, that's not a beating, bud
You did get advice, use the tapping on top of No3 cyl, it's cheaper, (the adaptor is around £8), and gives a better reading
Guest
Posts: n/a
lol. ok cool. can you please give any info on where no.3 cylinder is? are both fittings, i.e oil press and oil temp on the same cyl top ?
Trending Topics
Twatful
Joined: Apr 2003
Posts: 9,050
Likes: 0
From: Grew up and don't drive Scoobs anymore!
Easier to take off the IC to access the bung above the No3 cylinder, adaptor is LMA 067 from memory.
The pressure sender simply replaces the OEM one under the alternator.
This can be T'd in using another adaptor or replaced, since the OE version is pants mines replaced and the wire for the original cable tied to one side.
This doesn't throw a CEL on the dash.
The pressure sender simply replaces the OEM one under the alternator.
This can be T'd in using another adaptor or replaced, since the OE version is pants mines replaced and the wire for the original cable tied to one side.
This doesn't throw a CEL on the dash.
Scooby Regular
Joined: Jun 2008
Posts: 561
Likes: 0
From: Wigan
A sandwich plate makes the job a lot easier but to be honest the readings that you would get at the gauges would not be as accurate. There's not a lot of difference but if had bought Defi's then I would probably consider using the sensors like the other guys have suggested. Would love to see a photo when you have done the job ! Good luck mate !!
just taken delivery of a full set of Genome Defi gauges, full original Subaru kit from Japan.
And that comes with a sandwich plate for the oil temp and oil pressure, so its by no means a poor/bodge/wrong way of doing it.
Cant see how the gauges would read less accurately. Just it will read the pressure and temp at that point in its cycle through the engine.
Pics for anyone interested:
and in car, powered, but not fitted sensors yet (this weekends job!!)
And that comes with a sandwich plate for the oil temp and oil pressure, so its by no means a poor/bodge/wrong way of doing it.
Cant see how the gauges would read less accurately. Just it will read the pressure and temp at that point in its cycle through the engine.
Pics for anyone interested:
and in car, powered, but not fitted sensors yet (this weekends job!!)
gauges look great too
here: http://www.nippon-seiki.co.jp/defish...nual06064e.pdf
or if those aren't YOUR gauges, here: Defi - Gauges & Head up displays
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
Jan 11, 2021 03:08 PM
