OK - fitting a battery feed to an MY99
#1
Scooby Regular
Thread Starter
Right. Just got my MY99 DBM 4dr with AirCon.
Where the hell do I feed my amp's power from (from the battery - obviously!!)
As I've got Air-Con, there are NO grommets to get the cable into the the bl00dy car [img]images/smilies/mad.gif[/img].
Any ideas? And NO - I'm not keen on drilling through the bulkhead
There are also no obvious feeds on wither the driver's side or passenger side.....
I'm stuck
Answers on a postcard
Dan
Where the hell do I feed my amp's power from (from the battery - obviously!!)
As I've got Air-Con, there are NO grommets to get the cable into the the bl00dy car [img]images/smilies/mad.gif[/img].
Any ideas? And NO - I'm not keen on drilling through the bulkhead
There are also no obvious feeds on wither the driver's side or passenger side.....
I'm stuck
Answers on a postcard
Dan
#3
Scooby Regular
Thread Starter
Nice one Chiark!
Have you got any piccies of the grommet you used?
will let you know how i get on...
Dan
[Edited by ScoobyDoo555 - 12/22/2002 2:42:06 PM]
Have you got any piccies of the grommet you used?
will let you know how i get on...
Dan
[Edited by ScoobyDoo555 - 12/22/2002 2:42:06 PM]
#4
Scoobydoo,
You cannot miss it, it's where all the wires go through. The only tricky bit is finding it the other end. You need to be double jointed to get your hand and head up behind the fan unit behind the glove box
[Edited by gareth60 - 12/23/2002 9:18:31 AM]
You cannot miss it, it's where all the wires go through. The only tricky bit is finding it the other end. You need to be double jointed to get your hand and head up behind the fan unit behind the glove box
[Edited by gareth60 - 12/23/2002 9:18:31 AM]
#5
Scooby Regular
Thread Starter
Yes guys, found it
Have you lot fed into the grommet with the other cables (bit of a tight fit by the looks of it) or have you just fed the cable through a new hole in the grommet?
Obviously, gotta be careful if putting in a new hole!!!
Dan
Have you lot fed into the grommet with the other cables (bit of a tight fit by the looks of it) or have you just fed the cable through a new hole in the grommet?
Obviously, gotta be careful if putting in a new hole!!!
Dan
#7
Scooby Regular
Join Date: May 2001
Location: Surrey Somewhere, From 341 bhp '99 STI V to '98 Merc CLK & '00 Peugeot 306 XSI to '01 E46 M3 :)
Posts: 3,301
Likes: 0
Received 0 Likes
on
0 Posts
Did mine thru the same grommet, its tight, if you struggle put a little fairy liquid on the grommet, should then pull thru, tho you will need to be giving it a good old tug ooer
Trending Topics
#10
Scooby Regular
Thread Starter
Amp installed (with power too!!!)
Worked for about 5 mins before the Head Unit's 12V died.. [img]images/smilies/mad.gif[/img]
Not the Head Unit either...
Check out my other post
Thanks to all those who helped
Dan
Worked for about 5 mins before the Head Unit's 12V died.. [img]images/smilies/mad.gif[/img]
Not the Head Unit either...
Check out my other post
Thanks to all those who helped
Dan
Thread
Thread Starter
Forum
Replies
Last Post
matt12
ScoobyNet General
64
16 September 2015 09:16 PM
matt12
Engine Management and ECU Remapping
4
14 September 2015 09:36 AM