JDM Auto Intercooler Spray?
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Jan 2007
Posts: 2,914
Likes: 0
Received 0 Likes
on
0 Posts
JDM Auto Intercooler Spray?
Just thinking - could you convert the manual intercooler spray on an STI Type-UK to the auto spray that I believe the JDM STI has?
On initial thinking it should be as easy as putting, I presume, the themostatically controlled switch from the JDM system into the UK system. Is this so?
Bit of random curiosity really - but if its a simple add in job I might have a go at it.
On initial thinking it should be as easy as putting, I presume, the themostatically controlled switch from the JDM system into the UK system. Is this so?
Bit of random curiosity really - but if its a simple add in job I might have a go at it.
#3
Scooby Regular
iTrader: (4)
Join Date: Sep 2005
Location: The yorkshire dales - best roads in the UK
Posts: 3,311
Likes: 0
Received 0 Likes
on
0 Posts
My type ra runs water spray. I bought one of these:
eBay.co.uk: Turbo Boost Pressure Switch for Water Injection (item 260059786121 end time 30-Jan-07 18:30:46 GMT)
You can set it to spray at a preset boost level or just switch off when not needed.
eBay.co.uk: Turbo Boost Pressure Switch for Water Injection (item 260059786121 end time 30-Jan-07 18:30:46 GMT)
You can set it to spray at a preset boost level or just switch off when not needed.
#4
Ecu Specialist
The JDM new age STi water spray control is in the ecu and the switch just enables or disables it. Uk Sti rom doesn't have it.
Five different parameters have to be met for it to work. All are programmable when remapping.
bob
Five different parameters have to be met for it to work. All are programmable when remapping.
bob
#7
Scooby Regular
Join Date: Jun 2002
Location: Stoke-on-Trent
Posts: 674
Likes: 0
Received 0 Likes
on
0 Posts
Looking at the picture on this website http://www.type-25.com/images/conten.../engine_12.jpg ,the data table in the bottom left indicates the parameters to be: Coolant Temp, RPM, Boost Pressure, Vehicle Speed and Air Temp.
Perhaps Bob can advise the default values?
Best regards,
Ian
Perhaps Bob can advise the default values?
Best regards,
Ian
Last edited by IanK Spec C; 18 February 2007 at 03:14 PM. Reason: update
Trending Topics
#9
Scooby Regular
Join Date: Jun 2002
Location: Stoke-on-Trent
Posts: 674
Likes: 0
Received 0 Likes
on
0 Posts
Update-parameter values
I can now confirm from a MY07 Sti Spec C, the following values:
Coolant Temp > 80 Degrees C
Engine RPM > 4000
Boost Pressure 0.14 Bar
Vehicle Speed >188 Kmh (118MPH)
Air Inlet Temp > 20 Degrees C
The only thing I don't know is the algorthym to indicate how these are used to trigger the auto spray.
Best regards,
Ian
Coolant Temp > 80 Degrees C
Engine RPM > 4000
Boost Pressure 0.14 Bar
Vehicle Speed >188 Kmh (118MPH)
Air Inlet Temp > 20 Degrees C
The only thing I don't know is the algorthym to indicate how these are used to trigger the auto spray.
Best regards,
Ian
Thread
Thread Starter
Forum
Replies
Last Post
Flat4x4-again
General Technical
2
29 September 2015 06:32 PM