ScoobyNet.com - Subaru Enthusiast Forum
These are 10mm longer than our standard chrome parts.
These are 10mm longer than our standard chrome parts.
0 2021/03/27 01:08:57
After black painting the subaru hub centre, Id like to get some black wheel nuts in original quality and same 25mm length.
After black painting the subaru hub centre, Id like to get some black wheel nuts in original quality and same 25mm length.
0 2021/03/26 10:09:34
Is this an official Subaru part ? possible to order in the UK ?
Is this an official Subaru part ? possible to order in the UK ?
0 2021/03/26 09:54:41
0 2021/03/26 09:43:49
The WRX standard wheel nut assy
The WRX standard wheel nut assy
0 2021/03/26 09:41:13
0 2021/02/06 01:57:08
In direct comparison, I fitted a SC36 and this made 325lb/ft @ 4500 and
In direct comparison, I fitted a SC36 and this made 325lb/ft @ 4500 and
0 2021/02/06 01:50:08
0 2021/02/06 01:42:44
0 2021/01/22 01:19:24
0 2021/01/19 06:10:27
0 2021/01/19 05:55:25
These graphs are retesting power before/after fitment of the ported headers but without a map change. A slight drop since last dyno run.
These graphs are retesting power before/after fitment of the ported headers but without a map change. A slight drop since last dyno run.
0 2021/01/19 05:43:23
0 2021/01/18 10:31:45
TD05 16G versus SC36 alone has not made any real difference in the bottom end. Although it must be said mine is not the latest "SC36 R" Ball raced version
TD05 16G versus SC36 alone has not made any real difference in the bottom end. Although it must be said mine is not the latest "SC36 R" Ball raced version
0 2021/01/18 09:25:02
0 2021/01/18 09:22:25
Here the EJ207 , With its supported cross section 3, 6, 9 and 12
Here the EJ207 , With its supported cross section 3, 6, 9 and 12
0 2021/01/16 09:02:37
0 2021/01/16 09:01:42
0 2021/01/14 05:32:33
These look to have been soft , they shine a lot and have ragged edges from the form, which look potentially to me to be not properly cured or a raw material recipe or % issue.
These look to have been soft , they shine a lot and have ragged edges from the form, which look potentially to me to be not properly cured or a raw material recipe or % issue.
0 2021/01/14 05:27:01
These are on the front page of whitelines Internet site , My opinion above but ... you would need to QA these with a stress test / in the Lab. Typically to measure Shure hardness versus specification.
These are on the front page of whitelines Internet site , My opinion above but ... you would need to QA these with a stress test / in the Lab. Typically to measure Shure hardness versus specification.
0 2021/01/14 05:17:36
0 2021/01/11 12:45:14
This was the sample colour chosen
This was the sample colour chosen
0 2021/01/11 12:43:08
0 2021/01/11 07:20:22
0 2021/01/11 06:45:04
0 2021/01/11 06:45:02
0 2021/01/11 06:45:00
No problem Danny , here you go
No problem Danny , here you go
0 2021/01/11 02:04:38
0 2021/01/10 07:47:37
0 2021/01/10 07:47:06
0 2021/01/06 03:04:44
0 2020/12/30 15:48:04
0 2020/12/30 15:48:02
0 2020/12/30 15:47:59
0 2020/12/30 15:47:57
0 2020/12/30 15:47:54
The peak boost here is 1.45 bar and managed downward at 5750rpm
The peak boost here is 1.45 bar and managed downward at 5750rpm
0 2020/12/30 15:09:53
0 2020/12/17 06:55:43
0 2020/10/29 05:55:01
0 2020/10/29 05:51:55
0 2020/10/29 05:46:16