Rear Driveshaft info
#1
Rear Driveshaft info
I'm in the process of fitting a R160 4.4 plated rear diff into the long suffering rally car. I might be going over some old ground after reading earlier threads but by the look of things I cant use the original rear driveshafts especially the osr with the longer splines for the original diff.
Thanks
Huw
Thanks
Huw
#2
Scooby Regular
Join Date: Feb 2002
Location: oxfordshire
Posts: 657
Likes: 0
Received 0 Likes
on
0 Posts
hi huw
quite correct about the osr driveshaft,the longer part is used tyo drive the viscos part of the origional diff.two things to watch for.no1,the ciclip grove in the diff and the drive shaft linr up correctly(allegedly there are three different possition options for the groves...been there got the teeshirt!)
no2,when you have fitted the diff check the nsr inner driveshaft joint plunge.
i had 2 driveshaft failures because i was told to fit the short shaft to the nsr,turned out i needed the same shaft as the osr!hope this helps a bit and not confused you more
cheers neal
quite correct about the osr driveshaft,the longer part is used tyo drive the viscos part of the origional diff.two things to watch for.no1,the ciclip grove in the diff and the drive shaft linr up correctly(allegedly there are three different possition options for the groves...been there got the teeshirt!)
no2,when you have fitted the diff check the nsr inner driveshaft joint plunge.
i had 2 driveshaft failures because i was told to fit the short shaft to the nsr,turned out i needed the same shaft as the osr!hope this helps a bit and not confused you more
cheers neal
#3
Thanks for that Neal
Just so I've got this right your runing with both shafts with the longer splines? Also how do I check the grooves line up and nsr driveshaft joint plunge is correct.
Just so when my navigator calls 5 4 3 2 1 Go.... and we dont sit there looking stupid at the line going nowhere!!
cheers
huw
Just so I've got this right your runing with both shafts with the longer splines? Also how do I check the grooves line up and nsr driveshaft joint plunge is correct.
Just so when my navigator calls 5 4 3 2 1 Go.... and we dont sit there looking stupid at the line going nowhere!!
cheers
huw
#4
I have literally just been through this lot on my Hillclimb car.
You must not use the viscous shaft!
I did and the OSR jumped out (clip did not fuly locate in diff groove) and BANG
Get the right shafts from Welcome to the API website Call for David, and say 911 sent you.
The diff are gold dust and you dont want to risk it.
There are indeed 3 clip positions, and this is correct:
22B Bulletin Board: Snapped a driveshaft today with 380 x 360
Go to page dated 30 March 07 for the pic of what you must have.
Raced this weekend on slicks with drag starts, no probs.
Graham
You must not use the viscous shaft!
I did and the OSR jumped out (clip did not fuly locate in diff groove) and BANG
Get the right shafts from Welcome to the API website Call for David, and say 911 sent you.
The diff are gold dust and you dont want to risk it.
There are indeed 3 clip positions, and this is correct:
22B Bulletin Board: Snapped a driveshaft today with 380 x 360
Go to page dated 30 March 07 for the pic of what you must have.
Raced this weekend on slicks with drag starts, no probs.
Graham
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM