Need MAF Hose Adaptor or Housings
#1
I need a couple of adaptors that go from the 'MAF 4 bolt mounting plate' at one end to '89mm (3.5inch) hose fitting' at the other.
This is so that I can fit a silicon hose between my MAF and GGR filter, in order to place the cone in the wing.
Actually, a couple of dead MAF sensor would do - I can just chop the housings down to size, and bolt them back-to-back with the original fittings.
Anyone know where I could buy some adaptors, or does anyone have a couple of dead MAFs or housings that I could swap for a 24 pack of their preferred beer ?
Cheers
Steve
P.S. Here is a link to a picture, so you can see what I mean...I am separating the pink bit from the black bit !
This is so that I can fit a silicon hose between my MAF and GGR filter, in order to place the cone in the wing.
Actually, a couple of dead MAF sensor would do - I can just chop the housings down to size, and bolt them back-to-back with the original fittings.
Anyone know where I could buy some adaptors, or does anyone have a couple of dead MAFs or housings that I could swap for a 24 pack of their preferred beer ?
Cheers
Steve
P.S. Here is a link to a picture, so you can see what I mean...I am separating the pink bit from the black bit !
#2
Why not put an extension between the MAF and the induction hose, putting tha MAF flange in the wing (Extend black bit to blue bit )
All you need then is plastic round drainpipe and pipe to mate to MAF (lorry water pipe or old induction hose would do - or if you are feeling really brave superglue )
...CharlieP
All you need then is plastic round drainpipe and pipe to mate to MAF (lorry water pipe or old induction hose would do - or if you are feeling really brave superglue )
...CharlieP
#3
Hi Charlie,
Part of my reason for putting the cone in the wing is to distance it from the MAF, in order to cut down on MAF killing turbulence from the cone. Hopefully I'll have more laminar air flow through the MAF, once the cone is 18 inches from the MAF.
Cheers
Steve
Part of my reason for putting the cone in the wing is to distance it from the MAF, in order to cut down on MAF killing turbulence from the cone. Hopefully I'll have more laminar air flow through the MAF, once the cone is 18 inches from the MAF.
Cheers
Steve
#4
This afternoon, I'm off to pick up one MAF housing from a friendly tuner with a busted sensor.
That one will cost me 20 bottles of Stella !
Any offers for a second one ?
Cheers
Steve
P.S. I'm not tight - I know I promised a 24 pack, but they came in tens, and I couldn't fit three in a shopping basket :-)
[This message has been edited by StephenDone (edited 26 September 2001).]
That one will cost me 20 bottles of Stella !
Any offers for a second one ?
Cheers
Steve
P.S. I'm not tight - I know I promised a 24 pack, but they came in tens, and I couldn't fit three in a shopping basket :-)
[This message has been edited by StephenDone (edited 26 September 2001).]
#6
The APS duct is a solid piece of aluminium, very nicely made indeed.
I going to do a fitting guide today with pics, as soon as it is done I'll post it up for all to see
Cheers...
..CharlieP
I going to do a fitting guide today with pics, as soon as it is done I'll post it up for all to see
Cheers...
..CharlieP
#7
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:<HR>Originally posted by CharliePsycho:
<B>Steve,
Will your cone fit in the wing? I just put the APS kit in, and although there is quite a lot of space it may not be as enormouse as you think!!!
Also, make sure you mount the cone really well as it might get prone to rattling around in there, possible damaging itself.
...©[/quote]
Yes, there's room. I'm going to drop the cone a bit lower and round the overhang in your pic - I have ordered a 45 degreee bend to do this. I'll do some piccies too when the stuff turns up.
I'll bolt it down well.
Cheers
Steve
<B>Steve,
Will your cone fit in the wing? I just put the APS kit in, and although there is quite a lot of space it may not be as enormouse as you think!!!
Also, make sure you mount the cone really well as it might get prone to rattling around in there, possible damaging itself.
...©[/quote]
Yes, there's room. I'm going to drop the cone a bit lower and round the overhang in your pic - I have ordered a 45 degreee bend to do this. I'll do some piccies too when the stuff turns up.
I'll bolt it down well.
Cheers
Steve
Trending Topics
#8
Steve,
Will your cone fit in the wing? I just put the APS kit in, and although there is quite a lot of space it may not be as enormouse as you think!!!
Also, make sure you mount the cone really well as it might get prone to rattling around in there, possible damaging itself.
...©
Will your cone fit in the wing? I just put the APS kit in, and although there is quite a lot of space it may not be as enormouse as you think!!!
Also, make sure you mount the cone really well as it might get prone to rattling around in there, possible damaging itself.
...©
#9
>Anyone know where I could buy some adaptors, or does anyone have
>a couple of dead MAFs or housings that I could swap for a 24 pack
>of their preferred beer ?
>
I'm still on the lookout for one more dead MAF, and the beer offer still stands. Any takers ?
Steve
>a couple of dead MAFs or housings that I could swap for a 24 pack
>of their preferred beer ?
>
I'm still on the lookout for one more dead MAF, and the beer offer still stands. Any takers ?
Steve
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
Pro-Line Motorsport
Car Parts For Sale
2
29 September 2015 07:36 PM