EGT sensor on MY02
15 July 2003, 11:11 AM
#1
Scooby Regular
Thread Starter
Join Date: Aug 2002
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
Need to alter my EGT sensor as the power me car makes is causing an engine fault. I've been told to remove the sensor, fit a small bolt, and install a ohm resistor to give correct readings. One question...where is the EGT sensor on an MY02 - any pics would be great....
Anyone know a place to buy a 2.2k ohm resistor? Electronics shop maybe? Never been in one.
Anyone know a place to buy a 2.2k ohm resistor? Electronics shop maybe? Never been in one.
15 July 2003, 12:33 PM
#2
Scooby Regular
Join Date: Jul 2000
Location: Dull White BMW
Posts: 5,052
Likes: 0
Received 0 Likes
on
0 Posts
EGT probe is in the up pipe to the turbo. It's connector is on the left sde of the engine (bay from the front) and has two wires. Unplug the male connector and stick the 2.2kOhm in the female plug. I'd just leave the sensor in place. You can get a resistor from any electrical supplier.
Steve
Steve
15 July 2003, 12:44 PM
#3
Scooby Regular
Thread Starter
Join Date: Aug 2002
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
Cheers Steve...
I'm 80% I know which connector it is...it's under the small black plastic tray (with 2 thumb screws) and it's the lowest connector (the one with two black wires)?
2.2K ohm resistor here we come. I suppost I can use the male connector for a EGT gauge at a later date if I want...
I'm 80% I know which connector it is...it's under the small black plastic tray (with 2 thumb screws) and it's the lowest connector (the one with two black wires)?
2.2K ohm resistor here we come. I suppost I can use the male connector for a EGT gauge at a later date if I want...
16 July 2003, 10:23 AM
#6
Scooby Regular
Join Date: May 2003
Posts: 2,031
Likes: 0
Received 0 Likes
on
0 Posts
If you a running more power and a full system the EGT often goes. I got through 5 in mine until I placed the EGT in the downpipe. This was an option made available by Ian at Hayward & Scott 01268 727256.
Since fitting the downpipe and changing the EGT sensor to its new home where it is at least 150c cooler; I have had no problems whatsoever.....
Since fitting the downpipe and changing the EGT sensor to its new home where it is at least 150c cooler; I have had no problems whatsoever.....
Trending Topics
17 July 2003, 08:17 AM
#8
Scooby Regular
Join Date: Feb 2003
Posts: 337
Likes: 0
Received 0 Likes
on
0 Posts
I have an 02 WRX that had the same fault. I left the probe in place and fitted a 2.2k ohm resistor. You can buy them in any electrical type place and take 10seconds to fit. If you require further help feel free to email me.
18 July 2003, 11:47 AM
#11
Scooby Regular
Thread Starter
Join Date: Aug 2002
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
Fitted the 2.2K resistor yesterday and ECU light out instantly...lovely job. Tested my EGT sensor and it's gone for sure - don't think I'll bother with the re-location thing.
18 July 2003, 02:37 PM
#13
Scooby Regular
Thread Starter
Join Date: Aug 2002
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
Yeh, ace Pete...It was 7p inc the VAT...funny having VAT added to such a small amount!!
I've stopped looking at new EGT kits though as the sensor's are bloody expensive!
I've stopped looking at new EGT kits though as the sensor's are bloody expensive!
05 August 2003, 01:53 PM
#15
Scooby Regular
Thread Starter
Join Date: Aug 2002
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
Is it the correct rating? 2.2 needed (I tried a 2.4 before and that didn't work). Just need to 'plug' it into the female connector of the EGT. Then warning light goes out instantly the car starts.
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
