More engine pics :)
Subaru legacy con rods... Havent removed the STi ones yet, so cannot compare. Anyone else comment?
Half a block, and another half of a block
Crankshaft
Mitsubishi TD05 exhaust turbine
UK Legacy IHI VF12 turbine, and inlet. Flash a little bright
Non subaru... guess the crank....
You clamped whose car for being untaxed???? I dont think so Mr prescott....
New multi layer gasket, and Old composite gasket.
Shiny new oil pump
Half a block, and another half of a block
Crankshaft
Mitsubishi TD05 exhaust turbine
UK Legacy IHI VF12 turbine, and inlet. Flash a little bright
Non subaru... guess the crank....
You clamped whose car for being untaxed???? I dont think so Mr prescott....
New multi layer gasket, and Old composite gasket.
Shiny new oil pump
Scooby Regular
Joined: Nov 2001
Posts: 15,239
Likes: 1
From: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
not got a clue about the crank... Ill start the guessing at ford... I cant even tell how many cylinders it has with the picture... 
What was it you were saying about the oil journals??
What pistons are going back in?
David
What was it you were saying about the oil journals??
What pistons are going back in?
David
Crank is from my rover V8. Kinda my fault...when using a remote filter housing, make sure the oil is flowing the correct way through it..Most oil filters only flow in one direction, as I discovered to my cost.
You cant see what Im saying about the oil flow through the journals from the pics. Although if you look at the bearings in the block, Nos 1 3 5 have the groove in the bearing shell to supply oil flow to the crank, to supply the big end journals. The Crank GGR sell, has more oilways, and obviously bearings to match, to provide oilflow from main journals 1 2 3 4, to big end journals 1 2 3 4 ( although not specifically on any order.. )
They do not drill the crank at the rear, apparently for strength issues, and it is no longer necessary, due to the oil supply, from the other 4 main journals.
I will be using the STI4 pistons, I got sec. hand. See other pics...
F**K its costing a hell of a lot!!!!!!
Should get my bearings tomorrow, then just need a few new O rings and I can start sticking it together again, after I split another block to get me a crankshaft, this time from an engine with melted pistons... I have too much scrap lying about. Am I hard on a car, or is it just my imagination???
You cant see what Im saying about the oil flow through the journals from the pics. Although if you look at the bearings in the block, Nos 1 3 5 have the groove in the bearing shell to supply oil flow to the crank, to supply the big end journals. The Crank GGR sell, has more oilways, and obviously bearings to match, to provide oilflow from main journals 1 2 3 4, to big end journals 1 2 3 4 ( although not specifically on any order.. )
They do not drill the crank at the rear, apparently for strength issues, and it is no longer necessary, due to the oil supply, from the other 4 main journals.
I will be using the STI4 pistons, I got sec. hand. See other pics...
F**K its costing a hell of a lot!!!!!!
Should get my bearings tomorrow, then just need a few new O rings and I can start sticking it together again, after I split another block to get me a crankshaft, this time from an engine with melted pistons... I have too much scrap lying about. Am I hard on a car, or is it just my imagination???
Scooby Regular
Joined: Jul 2001
Posts: 241
Likes: 0
hehe love the wheel clamp
couldnt you find the ar-e ho-e who put it there and shove it where the sun doesn't shine!!
Respect!!!!!!!!
Oh and is crank from a vauxhall?
[Edited by simonzzr - 6/20/2002 8:33:07 PM]
couldnt you find the ar-e ho-e who put it there and shove it where the sun doesn't shine!!Respect!!!!!!!!
Oh and is crank from a vauxhall?
[Edited by simonzzr - 6/20/2002 8:33:07 PM]
Yep, the legacy IHI does seem to suffer cracks. Im using the Mitsubushi TD05 on my car though.
I should have pics of WRX crank and rods over the weekend, as I have to split another block, to get myself a crank, as the one in the pics is F*cked, which is the original legacy unit with 130,000 miles. Block, and bores are still mint too, as are the original pistons. The WRX engine im splitting, melted a psiton though, and bores are damaged. Doubt there will be much difference with the rods, but you never know...
I should have pics of WRX crank and rods over the weekend, as I have to split another block, to get myself a crank, as the one in the pics is F*cked, which is the original legacy unit with 130,000 miles. Block, and bores are still mint too, as are the original pistons. The WRX engine im splitting, melted a psiton though, and bores are damaged. Doubt there will be much difference with the rods, but you never know...
Trending Topics
Scooby Newbie
Joined: Dec 2001
Posts: 21
Likes: 0
do you self a favour and get stronger billet conrods with arp bolts when you are putting the engine back together
the conrods out of a sti are the same as legacy and on the colour might be different eg red
you can buy them from the states really cheap
I have sourced crower billet rods (4340 steel for 600 us dollars)
It will save you heaps in the long run
regards
try www.isrperformance.com
the conrods out of a sti are the same as legacy and on the colour might be different eg red
you can buy them from the states really cheap
I have sourced crower billet rods (4340 steel for 600 us dollars)
It will save you heaps in the long run
regards
try www.isrperformance.com
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
Jan 11, 2021 03:08 PM
BlueBlobZA
Member's Gallery
30
Jul 25, 2016 09:14 AM
Bazil_SW
Engine Management and ECU Remapping
24
Sep 21, 2015 11:55 PM