Erh you didn't look properly ??

I think he is UK based

 

Got my prodrive logos today, only ordered them Thursday eve from rc graphics, great service..!

I can highly recommend them, good quality and prompt P&P

Jason.

 

Jase,

RC or RS Graphics?

Were they a special order size.

Given the size that you go, would you have ordered them bigger next time?

 

Well, I have just cut mine out and applied the glittery STi logos... I'll tell you this for free - cutting this material is a nightmare! I got hand cramp, got through 2 Stanley blades finally opting for a pair of garden secateurs to do the long straits LOL.

I must say they are looking dandy - and Paul37 is fitting them on Thursday. I shall then gleefully post pics of my new flaps

 

Hope I get 'em on straight

 

If you don't we can always reposition the graphics LOL

 

Do you mean racegraphics or rsgraphics ??

I got a quote for 6" long ones but think that may be too big.

Also what price did you manage to get them for (if you dont mind me asking!) ?

 

Those with classics, how low do your front flaps hang? Mine seem rather short.

 

Only got through two blades !!! No wonder it was tough

I also got hand cramp oh and managed to cut the corner of one of my fingers off and bleed all over the template !!
It f**kin hurt

Worth it in the end though

 

Have you got a classic Mark? Most of the other cars I have seen photos of are the newer shaped ones and their flaps look long - mine however and extremely short. I only chose small logos for mine but the front ones are hidden by the bodywork

 

No sorry I have a newage.

Here is a picture of my front flaps :-




Don't know how that compares to yours ???

Which set of holes did you use on the templates ??
I went for the bottom set as I plan on having it lowered, and couldn't be ar$ed to re-fit them !!
if I had used the upper set of holes it would have lowered the flaps by approx 25mm, not sure if that is any help to you ??

Post some pics up and let us see

 

dannyboyturbos look aout right:-

http://bbs.scoobynet.co.uk/showthread.php?t=427237

 

Dam just beat me to it Austen !!!

 

austen wrx

I know im abit late, is there any chance i can get a set of brackets please

Andy.

 

Put it this way, there is no overhang of material above the brackets so all available length has been used.

It's dark now (just been to work) so will take piccies tomorrow and post up. Mine are a lot less length than you show.

 

I'm wondering if you have fitted the brackets too high??

 

Nope, used the holes as per the instructions .... let me go take some piccies

 

That's the front flap. logo about one centemeter above the baseline.

 

mmm, that looks about right from what i 've seen fitted to other classics. If the flaps are too long they drag when cornering. On my newage i have eibachs and uprated ARB and have a 30mm gap between the ground and the flap and it doesn't catch, but when i had standard springs and ARB with the the flaps set on a 30mm gap (lowest setting on newage templates) they dragged like hell!! I was going to raise them to 60mm of the ground but then had springs and ARB done instead

 

Austen - could I be a pain and ask for the templates to be faxed to me - as the cutting method I used destroyed the templates, and as such, I do not have drilling guides (I was going to use the bracket for where to drill) but if there are 2 different height options I may have made a mistake !

 

Classics only have 1 height setting, just line the tops of the brackets up with the tops edges of the flaps

 

Cool - that is what I thought - but reading the above comments made me $hit me pants!

 

You had better go and change them now then

 

They'll be OK, I'll just spoon the lumps out!

 

Austen,

The Autocad newage template you e-mailed me only had one set of holes - is this correct ??

 

arh, i think i must have sent you and earlier drawing with only one set on (highest rear and lowest front)

 

Ahh that explains it - slightly too low on front and slightly too short on the back.

Could you e-mail me one with both sets of holes on them please, so that I can make adjustments to my new set (and put the extra holes in the ones I am trying to sell http://bbs.scoobynet.co.uk/showthread.php?t=430190)

Thanks

Darren

 

YHM

 

Cheers mate.

You really are a top bloke !

 

i'm even better after i get my crate of stella