Possible H&S Backbox Group Buy
Oh, didn't realise it was a question. 
In charge of power generation / utilities at the moment so yeah, it's usually me that shuts it down.
What about yourself?
PS: go'an tell us next time you're shutting down. Our CRT doesn't like it when the gas stops flowing. 
PPS: have a pint for me.
In charge of power generation / utilities at the moment so yeah, it's usually me that shuts it down.
What about yourself?
PS: go'an tell us next time you're shutting down.
Our CRT doesn't like it when the gas stops flowing. PPS: have a pint for me.
260bhp the last time it was checked mate, hopefully a little more the next time it goes on the RR. 
Of course, if i could stuff one of the Rolls Royce GT's off here in my kit bag and fit it to the Scooby it may up the figure a little.
Back on Tuesday weather depending, too much sunshine and no fog for over a week doesn't bode well.
Of course, if i could stuff one of the Rolls Royce GT's off here in my kit bag and fit it to the Scooby it may up the figure a little. Back on Tuesday weather depending, too much sunshine and no fog for over a week doesn't bode well.
..........cheers Hayward and Scott...
Scooby Regular
Joined: Nov 2003
Posts: 46,493
Likes: 13
From: riding the crest of a wave ...
Youll be pleased with the outcome.........btw there not 14 mm bolts -17 on mine....also 3rd hangar rubber in front o box seems to have disappeared 
otherwise would a been 5 minute job ( with ramps) i used the curbside
...also no gasket in between jus mid section ta go . then mybe apexi fc ? + remap
otherwise would a been 5 minute job ( with ramps) i used the curbside...also no gasket in between jus mid section ta go . then mybe apexi fc ? + remap
Thread Starter
Scooby Regular
Joined: Jan 2003
Posts: 846
Likes: 0
From: County Durham
How's the fit of yours??
Did mine this morning, and it looked like it was tight just to the side of the diff. Went for a run, and at certain speeds and certain revs, it feel like the dash is going to fall apart due to the vibrations. Also, above 60, it's like sitting on a wacka plate (used for compacting dolomite etc, vibrates a lot), not as severe, but your *** does get a good massaging.
Think I'll have to take it off and re-seat it, these vibrations can't be right.
Andy.
Did mine this morning, and it looked like it was tight just to the side of the diff. Went for a run, and at certain speeds and certain revs, it feel like the dash is going to fall apart due to the vibrations. Also, above 60, it's like sitting on a wacka plate (used for compacting dolomite etc, vibrates a lot), not as severe, but your *** does get a good massaging.
Think I'll have to take it off and re-seat it, these vibrations can't be right.
Andy.
Scooby Regular
Joined: Nov 2003
Posts: 46,493
Likes: 13
From: riding the crest of a wave ...
there is vibration on mine but not against any thing metal jus normal id ave thought - i dont have forward rubber (hanger) at the mo also ...........................*** ta think did have bit o a headache yestday eve .....but have slight nasal blockage last couple o days
Thread Starter
Scooby Regular
Joined: Jan 2003
Posts: 846
Likes: 0
From: County Durham
Been out in it again this afternoon, and it seems to have settled down a bit, but there is still some vibration there.
Going to take it off anyway and re-seat it to see if it gets any better.
Andy.
Going to take it off anyway and re-seat it to see if it gets any better.
Andy.
Thread Starter
Scooby Regular
Joined: Jan 2003
Posts: 846
Likes: 0
From: County Durham
Had a look, and I'm pleased I did. It was touching the driveshaft, and as the shaft turned, it was wearing away the pipe!! If I'd left it, I doubt it would have lasted a week before it holed.
A quick call to Ian, and he recommended bending the hangers upwards to drop the exhaust closer to the floor. Getting it off wasn't too easy, but give them a few whacks, put it back on, and I can now get my fingers in between the pipe and the shaft. Vibrations have gone, and it's not too low so it hits the speed bumps.
I love a happy ending.
Andy.
A quick call to Ian, and he recommended bending the hangers upwards to drop the exhaust closer to the floor. Getting it off wasn't too easy, but give them a few whacks, put it back on, and I can now get my fingers in between the pipe and the shaft. Vibrations have gone, and it's not too low so it hits the speed bumps.
I love a happy ending.
Andy.
Mine arrived yesterday. But MOT today so i was retro-fitting the cat'd centre yesterday rather than the BB.
Awaiting the arrival of the gasket and then the stainless H&S centre will be going back on along with the BB.
But MOT today so i was retro-fitting the cat'd centre yesterday rather than the BB. Awaiting the arrival of the gasket and then the stainless H&S centre will be going back on along with the BB.
Sorry to hear that Justin.
Mine is now on and **** it's loud!!
Passed the MOT this morning so swapped the old PPP back box and rusty cat'd centre for my H&S centre and brand new BB. Did it on a two-poster and all seems well, no leaks or owt, just loads of noise!
Special thanks to my local dealer (the one in Aberdeen to the local peeps...) who managed to give my gf the wrong gasket after i specifically asked for one to be set aside for me yesterday. She even told them it was for a '98 UK Turbo after me telling them the exact model/year of car yesterday... As the car was on the ramps at the time i went up to the local exhaust/tyre place with the PPP box where they found a similar (and correctly sized) one and was told to stick it in my pocket.
Justin, it'll be worth the wait, don't worry.
Mine is now on and **** it's loud!!
Passed the MOT this morning so swapped the old PPP back box and rusty cat'd centre for my H&S centre and brand new BB. Did it on a two-poster and all seems well, no leaks or owt, just loads of noise!
Special thanks to my local dealer (the one in Aberdeen to the local peeps...) who managed to give my gf the wrong gasket after i specifically asked for one to be set aside for me yesterday. She even told them it was for a '98 UK Turbo after me telling them the exact model/year of car yesterday...
As the car was on the ramps at the time i went up to the local exhaust/tyre place with the PPP box where they found a similar (and correctly sized) one and was told to stick it in my pocket. Justin, it'll be worth the wait, don't worry.
I thought it might sound a little harsh if you know what i mean? It doesn't though, just sounds meaty kinda!!
It made a bit of a din on my way back home though. I did have the back seats down however. Will see how it fairs in the long run.
It made a bit of a din on my way back home though. I did have the back seats down however. Will see how it fairs in the long run.
Scooby Regular
Joined: Apr 2004
Posts: 108
Likes: 0
From: Peterhead
Originally Posted by Carl Davey
I thought it might sound a little harsh if you know what i mean? It doesn't though, just sounds meaty kinda!!
It made a bit of a din on my way back home though. I did have the back seats down
however. Will see how it fairs in the long run.
It made a bit of a din on my way back home though. I did have the back seats down
however. Will see how it fairs in the long run.
Originally Posted by jmc1968
Have you had any probs with the system rubbing against anything?
