Hull Scoobs sign in please
I now have my knocklink in my gauge pod, remote mounted leds, works quite well.
The lambda link, i had attached to the dash just behind the indicator stalk, so you could see the lights when driving straight and the indicator was off. Again worked well.
The lambda link, i had attached to the dash just behind the indicator stalk, so you could see the lights when driving straight and the indicator was off. Again worked well.
Thread Starter
Scooby Regular
iTrader: (2)
Joined: Jan 2003
Posts: 1,587
Likes: 0
From: Lofty in Hull
Originally Posted by P20SPD
why did they touch the idle stepper? if thats been fiddled with, it can easily thow it out of sink.
i will await compression figures
i will await compression figures
(Sorry, couldn't resist
I'll get me coat..............
)
thought you lot would understand if i put it in your language
Bryn, good news on one side, which side 2 & 4 or 1 & 3
Ring me if you need to try my lambda sensor tonight.
Bryn, good news on one side, which side 2 & 4 or 1 & 3
Ring me if you need to try my lambda sensor tonight.
Scooby Regular
Joined: Jan 2003
Posts: 684
Likes: 0
Lofty - yes Phil @ Welptons when we all got a £25 off voucher.
I had bought 5 litres of Mobil 1 0w40, K&N performance panel filter and denso iridium plugs from GGR.
Phil advised me the oil should be a little heavier and used the Magnatec 5w40. The air filter we didn't use because it was oil impregnated and apparently oil sticking to MAF sensor causes the twin headed goatlike cupped feet four arsed bastad to appear.
Mr D - Before the service mentioned above - just after getting the car - it did have an idle problem, like it has now but nowhere near as bad. Phil cleaned out the stepper and it was fine. He advised that the steppers can go on P1's and as they are derivatives of the Type R, this may well be a similar issue as they both use the same stepper.
Phew
I had bought 5 litres of Mobil 1 0w40, K&N performance panel filter and denso iridium plugs from GGR.
Phil advised me the oil should be a little heavier and used the Magnatec 5w40. The air filter we didn't use because it was oil impregnated and apparently oil sticking to MAF sensor causes the twin headed goatlike cupped feet four arsed bastad to appear.
Mr D - Before the service mentioned above - just after getting the car - it did have an idle problem, like it has now but nowhere near as bad. Phil cleaned out the stepper and it was fine. He advised that the steppers can go on P1's and as they are derivatives of the Type R, this may well be a similar issue as they both use the same stepper.
Phew
Scooby Regular
Joined: Nov 2004
Posts: 2,097
Likes: 0
From: humberside
OH NO !! not the twin headed goatlike cupped feet four arsed bastad .
sorry flame suit on
bryn,, Phil told me to use shell hellix(mybe bad spelling)
sorry flame suit on
bryn,, Phil told me to use shell hellix(mybe bad spelling)
Last edited by scoobymods; Nov 19, 2004 at 02:53 PM. Reason: forgot about oil
Thread Starter
Scooby Regular
iTrader: (2)
Joined: Jan 2003
Posts: 1,587
Likes: 0
From: Lofty in Hull
Sounds like a good idea but does remote mounting the leds involve the use of ribbon cable and solder???? Hmmmm, recipe for disaster there then!!!
I've gotta do summat tho or I'm gonna end up rear-ending someone (oo-er missus) if I carry on looking down into the footwell whilst driving hard
Don't think my interior trim will take much more ripping out and shoving in again, it's all starting to get loose and rattly 'cos it's been in and out so many times!! I think I've buggered up the wiring on my GPS stuff as well now - it don't seem to work since I installed the Links
I've gotta do summat tho or I'm gonna end up rear-ending someone (oo-er missus) if I carry on looking down into the footwell whilst driving hard
Don't think my interior trim will take much more ripping out and shoving in again, it's all starting to get loose and rattly 'cos it's been in and out so many times!! I think I've buggered up the wiring on my GPS stuff as well now - it don't seem to work since I installed the Links
Scooby Regular
Joined: Jan 2003
Posts: 684
Likes: 0
Remote mounting LED's
Thread Starter
Scooby Regular
iTrader: (2)
Joined: Jan 2003
Posts: 1,587
Likes: 0
From: Lofty in Hull
Originally Posted by HOUSEQUAKE
pmsl
Just been outside for a smoke and looked at my car - might have to pop round to BJ's tomorrow to see if he can pull out the knee-shaped dent in my front wing
Scooby Regular
Joined: Nov 2004
Posts: 2,097
Likes: 0
From: humberside
Originally Posted by Scooby New
Just been outside for a smoke and looked at my car - might have to pop round to BJ's tomorrow to see if he can pull out the knee-shaped dent in my front wing
Thread Starter
Scooby Regular
iTrader: (2)
Joined: Jan 2003
Posts: 1,587
Likes: 0
From: Lofty in Hull
Right I'm off home shortly.
Pum (doh! I mean scoobymods) I'll give you a bell 2moro. Not sure what I'm doing yet, got a few things to do but will ring when I know more.
Bryn, if you need anything gimme a ring.
See you all on Sunday.
Mr D - get yer **** there on Sunday
Pum (doh! I mean scoobymods) I'll give you a bell 2moro. Not sure what I'm doing yet, got a few things to do but will ring when I know more.
Bryn, if you need anything gimme a ring.
See you all on Sunday.
Mr D - get yer **** there on Sunday
Thread Starter
Scooby Regular
iTrader: (2)
Joined: Jan 2003
Posts: 1,587
Likes: 0
From: Lofty in Hull
Pum -
Bryn - that don't sound right to me. Does yours have a check engine light? Has this been on? When my Lambda sensor was fecked the CEL came on. Has Phil had a look? With the Select monitor you can instantly tell if it's not working right. But I don't know if the Select monitor is compatible with yours. Best bet would be to try one of Mr D's lambda sensors and see if that solves it. If you need a lift up there tomorrow gimme a bell.
Bryn - that don't sound right to me. Does yours have a check engine light? Has this been on? When my Lambda sensor was fecked the CEL came on. Has Phil had a look? With the Select monitor you can instantly tell if it's not working right. But I don't know if the Select monitor is compatible with yours. Best bet would be to try one of Mr D's lambda sensors and see if that solves it. If you need a lift up there tomorrow gimme a bell.
Scooby Regular
Joined: Aug 2003
Posts: 2,589
Likes: 0
evening all...
header tank sorted after weld....
gun'er get it washed and bring round to colbies sat am to grind out the bracket we where talking about for saftey.
hope all you other cars/owners have sorted the problems that seem to be appearing over the last few days!!
ads
header tank sorted after weld....
gun'er get it washed and bring round to colbies sat am to grind out the bracket we where talking about for saftey.
hope all you other cars/owners have sorted the problems that seem to be appearing over the last few days!!
ads
