3D Printed Front Door Speaker Spacers
#1
3D Printed Front and Rear Door Speaker Spacers
Hi all,
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- newage fronts (either 6.5" or 5.25" speakers) and rears (To fit 5 1/4" speakers) - variant 1
- classics - variant 2
Costs
Newage fronts 6.5": £17.50 + postage gifted on PayPal
Newage fronts 5.25": £16.00 + postage gifted on PayPal
Newage rears 5.25": £15.00 + postage gifted on PayPal
Classic fronts 6.5" = £16.00 + postage gifted on PayPal
Postage is: £2.95 RM 2nd class, £3.50 RM 1st class.
These can be printed to order and I will need about 48 hours before shipping. PM me for ordering.
Cheers for looking!
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- newage fronts (either 6.5" or 5.25" speakers) and rears (To fit 5 1/4" speakers) - variant 1
- classics - variant 2
Costs
Newage fronts 6.5": £17.50 + postage gifted on PayPal
Newage fronts 5.25": £16.00 + postage gifted on PayPal
Newage rears 5.25": £15.00 + postage gifted on PayPal
Classic fronts 6.5" = £16.00 + postage gifted on PayPal
Postage is: £2.95 RM 2nd class, £3.50 RM 1st class.
These can be printed to order and I will need about 48 hours before shipping. PM me for ordering.
Cheers for looking!
Last edited by Bazil_SW; 15 December 2018 at 06:07 PM.
Trending Topics
#10
Scooby Regular
Hi all,
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- confirmed: Hawk
- presumed all newage as the same speakers and door casings were used on earlier models
- presumed classics (assume same hole centres for the stock 3 screws. i.e. 150m if you measure centre to centre between any 2 of the mounting holes)
Cost: £17.50 + postage gifted on PayPal
Postage is: £2.50 RM 2nd class, £3.50 RM 1st class.
These can be printed to order. PM me for ordering.
Cheers for looking!
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- confirmed: Hawk
- presumed all newage as the same speakers and door casings were used on earlier models
- presumed classics (assume same hole centres for the stock 3 screws. i.e. 150m if you measure centre to centre between any 2 of the mounting holes)
Cost: £17.50 + postage gifted on PayPal
Postage is: £2.50 RM 2nd class, £3.50 RM 1st class.
These can be printed to order. PM me for ordering.
Cheers for looking!
#11
Can do, if you can confirm the distance between 2 opposite mounting holes on your speakers that would help. I think it's 118mm from what I can find, but there seems to be some variation. They can be slightly cheaper too since they will be smaller, can work out it later.
Cheers!
Cheers!
#14
Scooby Regular
#16
I’ll take a set please mate.
Measured my home made mdf spacers from a previous classic I had and they are 15cm between the 3 mounting points
please pm payment details
Paul
Measured my home made mdf spacers from a previous classic I had and they are 15cm between the 3 mounting points
please pm payment details
Paul