3D Printed Gear Knobs with Logo
#1
3D Printed Gear ***** with Logo
Hi,
I've added a new product to my line up of 3D printed scoobs mods.... Gear ***** with logos
Colours
Various available, but I usually have stock of black, blue (light or dark, and baby), red, silver, yellow (new), and white filament
Variants
Flat top - see image
Round top - see image (for the 'production' parts the print seam will be at the front!)
Logos
Currently I have designs for STi and WRX, but probably can do others if there is a enough request
Fitment
- M12 x 1.25 thread (newage, hatch and presumably WRX STi models, maybe classics too?)
- reverse lockout compatible
- the threads are slightly undersize to ensure a really tight fit that will resist rotation during use, I will provide a little piece of grippie rubber mat so you can tighten it on. It requires 2 or 3 times of winding on and off to clean the threads and ensure a snug fit that will bottom out the threads
Design
- 2 piece design. PLA material for the outer visual part as it prints better and provides a smoother finish, and with a PETG plastic insert (more durable than PLA) for the threaded piece
- printed in solid plastic, they weigh around 75g for the flat top and 80g for the round top (roughly half of the 6 speed newage stock part), so they have a nice solid feel to them
- the logos are inset and completely flush on the round top, and 'as near as' flush on the flat top ones
Cost
Flat = £10 + £3.50 UK RM 1st Postage (gifted on paypal)
Round = £11.50 + £3.50 UK RM 1st Postage (gifted on paypal)
PM for details
Disclaimer
This is intended as a decorative piece and whilst it is functional you must ensure that it is secure and suitable before use. I can not and will not accept any responsibility for injury or incident that occurs as a result of its use.
Thanks for looking!
I've added a new product to my line up of 3D printed scoobs mods.... Gear ***** with logos
Colours
Various available, but I usually have stock of black, blue (light or dark, and baby), red, silver, yellow (new), and white filament
Variants
Flat top - see image
Round top - see image (for the 'production' parts the print seam will be at the front!)
Logos
Currently I have designs for STi and WRX, but probably can do others if there is a enough request
Fitment
- M12 x 1.25 thread (newage, hatch and presumably WRX STi models, maybe classics too?)
- reverse lockout compatible
- the threads are slightly undersize to ensure a really tight fit that will resist rotation during use, I will provide a little piece of grippie rubber mat so you can tighten it on. It requires 2 or 3 times of winding on and off to clean the threads and ensure a snug fit that will bottom out the threads
Design
- 2 piece design. PLA material for the outer visual part as it prints better and provides a smoother finish, and with a PETG plastic insert (more durable than PLA) for the threaded piece
- printed in solid plastic, they weigh around 75g for the flat top and 80g for the round top (roughly half of the 6 speed newage stock part), so they have a nice solid feel to them
- the logos are inset and completely flush on the round top, and 'as near as' flush on the flat top ones
Cost
Flat = £10 + £3.50 UK RM 1st Postage (gifted on paypal)
Round = £11.50 + £3.50 UK RM 1st Postage (gifted on paypal)
PM for details
Disclaimer
This is intended as a decorative piece and whilst it is functional you must ensure that it is secure and suitable before use. I can not and will not accept any responsibility for injury or incident that occurs as a result of its use.
Thanks for looking!
Last edited by Bazil_SW; 18 August 2018 at 08:55 AM.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Bazil_SW
Subaru Parts
7
09 November 2021 08:10 PM
Bazil_SW
Subaru Parts
6
07 December 2018 07:27 PM