DGodden87

Can a blob eye be converted to a hawk eye, the interior is the same and so is the side and rears so would imagine it would only be the 2 front wings, bonnet, bumper and grill.

Would it just be a case of bolt off, bolt on??

tubbytommy

iTrader: (20)

someone has done a conversion on here,
i think it was a bug to hawk though and looks like a whole lot of work maybe cheaper to sell the blob and buy a hawk.

TonyBurns

iTrader: (3)

I dont think its as easy as you think, the intercooler is different to start with, and you would have to change that if you did the conversion (so you may require a remap).

Tony

Scooby Dan

Obviously you would need the headlights which cost £931 each from Subaru and are near impossible to source second hand. I have been looking for a drivers side one for weeks without any luck.
I think you would also need the front panel too.

DGodden87

Intercooler wouldnt be a problem as its coming off the road shortly for an engine build etc so a front mount will be going in!

Headslight i can get from a couple of places 2nd hand so thats not a problem either.
The front panel would just be a case of cutting the old one out and rewelding a new one in

scoobysteve35

Hi mate defo possable i drive one :-) not sure how much work is involved as i brought it like this but got seats and door cards out the hawk too but blob dash

wr pete

iTrader: (1)

You will need the bonnet, intercooler shroud (if using top mount) front wings, front panel,(not radiator support ) front plastic wheel arch liners, front bumper and bumper support, headlights, the front part of the inner wings need cutting slightly to meet up with the front panel, (bug eye not sure about blob) but should be very sim, headlight wiring needs modifying for new lights, headlight washers need pluming in and thats about it to be honest. all this was done on a 2003 bug eye but i had a damaged car to take all the parts from, it could be costly to buy all you need separately, hope this helps some.

Rice Rocket

iTrader: (23)

I'm in the middle of doing this now to my bugeye.

Bonnet
front wings
inner liners (not 100% sure yet)
front bumper
possible bumper support bar unless your going fmic
radiator support bar
Headlight supports (underside of headlights)
headlight support brackets
Wiring!! what an a$$ of a job
Drilling out spot welds (16 in total)
Cutting the inner wings away
aligning up above before finalising and replacing the rusty panels you find behind it all lol

Alot of work but worth it.

Ricey

SkydiveMacca

I think chargespeed do a conversion kit to help make things fit?

Luckyscoob

iTrader: (2)

and to be really fussy, the plastic rear wheel arch extensions, as the hawk has a wider track. , oh, and diffuser and rear lights. Oh and boot lid with the centre badge and of course the top spoiler above the back window. No point in doing the front and not the back!.

eggy790

iTrader: (20)

this post scares the crap outta me, ive just bought a front end lol when you say rewiring headlights.. what do you mean?

i have both headlights and they have been unplugged via their connectors.. assumed they would plug straight into my bug connectors?

ive got an aftermarket hid kit on the bugeye, would that work with it? the hawkeye headlights are hid anyway but wasnt sure if that would wire up fine..

im confuzzled.

Rice Rocket

iTrader: (23)

I have the sti headights and its not a direct plug n play, thay need rewired I have 1 plug on the back of the lights and different plugs from the OE bugeye lights, I have been trying to figure this out for ages! lol Time for an auto sparky!!

Good luck when you start yours. PM me pics of the back of the lights and i'll see if its the same as mine.

Ricey

wr pete

iTrader: (1)

Here are some pics of my hawk conversion, all done by me in my garden

rickya

iTrader: (18)

Great work WR Pete!

Rice Rocket

iTrader: (23)

Nice job Pete, cheers for the PM.

Ricey

st03eko

iTrader: (1)

Here some of mine as well got it all done by ABW who is on here I beleave

DisoDisp

iTrader: (1)

what rear diffuser etc is that, looks interesting with the spats.

verdasco1

Flippin eck St03eko... how nice is your car, that is one of the nicest scoobys i´ve seen!

The nicest is this one though...

https://www.scoobynet.com/680057-haw...eplica-14.html

Its ABW´s work if you read the thread all the info is there...

verdasco1

wooaaaaahh can´t get over how nice that matt black wrap hawk is... you got a thread on that project st03eko? If not you should start one with all the photos! That car is crisp with a kapital K!

Those pics have just shone a bit of light on a mega boring day...thanks for sharing!

st03eko

iTrader: (1)

Will do one tonight. She's not bad for a WRX lol.

wr pete

iTrader: (1)

Thanks for the comment mate, cheers

wr pete

iTrader: (1)

Cheers mate, good luck with your car

DisoDisp

iTrader: (1)

Aye I did read it was ABW kit, but can't find that rear diffuser on the ABW site.

st03eko

iTrader: (1)

The front of the car is off the time attack cars. The rear is off the Japspeed drift car. The rear arch's are from the classic wide arch kit. A bit of mix and match. Standard sports bonnet. I'm getting the vents fitted to that soon.

Rice Rocket

iTrader: (23)

Have to say thats a cracking picture!! Your scoob looks awsome too.

What are your mods and defo get a project thread up! Heard about the vents that a certain top bloke was doing, very nice. ;0)

Ricey

verdasco1

ok i´ve changed my mine it´s not one of the best i´ve seen...it IS the best i´ve seen!