558BHP CATALUNYA NOW BREAKING MORE PARTS ADDED
 

Ok i have decided that if the car is not sold within the next week i will be breaking it :(

I want to sell the engine and gearbox before i advertise the smaller bits and pieces, i will list engine and box spec and prices now then add other bits when i have sold them on.

2.1 Jun/cosworth ej20 cdb bare long block

- EJ20 CDB
- acid-dipped, media blasted and threads retapped
- rear thrust conversion
- 14mm head-stud conversion
- 0.5mm bore and hone
- faces skimmed.
- Cosworth 92.5 mm stroker pistons
- Jun stroker con rods
- Centre thrust 79mm crank shaft
- Cosworth 14mm head stud and dowel conversion
- ACL race big and and main bearings
- RCM uprated oil pump
- 4 layer uprated head gasket set
- V4 heads, heavily ported and polished, Jun 272/272 cam shafts with
cosworth 14mm head stud conversion

One of the block halves had a very small hairline crack on the external waterway so was professionally repaired, this consisted of V'ing out the crack slightly, heating the block and alloy welding it, this shouldn't and will not affect the price of the engine, it has been tested etc and inspected and does not/will not be any cause for concern.
The engine has done around 1600 miles of which 1000 were running in miles, it has always been run on motul 300v competion and has seen no more than 1.8bar boost. This engine was built for high boost and big power

ENGINE SOLD

OR can be sold as a complete ready to run long block as above but including

-Phase 1.5 black inlet manifold including parallel rails, braided lines, turbo smart fpr, billet inlet manifold spacers, mad hammer catch can with piping, 1000cc phase 2 injectors with adapters, black alternator, ps relocation kit, etc all ready to drop in and bolt up and run, just add headers etc.

ENGINE SOLD


Gearbox


PPG 5 speed dog box, recently refreshed by Paul at zen and since done around 600 miles.
Proven on 9 second drag cars.
You'd be hard pushed to find a gearbox with a spec like this for this price.

- PPG 1-4 dog kit, straight cut gears.
- OE helical 5th gear
- Billet selector forks
- Cusco RS 1.5-way LSD
- Modena centre diff with straight-cut billet drop gears, very rare
- Black powder coated casing which is mint
- Ratios: 3.18 / 1.87 / 1.32 / 0.95 / std

£3000


OR For £4000 ill do the box with 2x front shafts, 2xrear r180 shafts, prop shaft, R180 rear diff, R180 rear hubs and a 5 speed exedy hyper twin plate clutch that had 2x new plates and new release bearing fitted around 600 miles ago.

NEW PARTS ADDED 21/3/13

10x18 et20 rota fighter drifts in matt black with very good condition Toyo r888 tires £900


Syvecs S6 pnp inc jt innovations wide band kit, jt innovations ait sensor kit, 8position cal switch £1100
SYVECS PROVISIONALY SOLD

Whiteline front arb 22mm with bushes, whiteline rear arb 24mm with bushes and whiteline heavy duty mounts £150
ARBS SOLD

Fuel set up, Walbro 225lph intank pump, Bosch 044 inline pump, sytec inline filter, swirl pot, using push on (normal) hose and clamps £400

Exedy hyper twin plate clutch, 5 speed, fitted with new plates and bearings 600 miles ago.
£750

Defi 60mm white face guages, boost, oil temp, oil press with all sensors and wiring and controller plus triple pod holder £500

Rear Brembo gold 2 pots in good condition fitted with brand new pagid pads will come with unused braided lines and oe discs with a bit of wear £225

High spec monster 6 pot front calipers, good condition, these have been half painted red, comes with grooved discs in good condition and ferodo ds2500 pads in good condition, comes with braided lines £500

Gruppe s2 2 bolt headers wrapped £200
HEADERS SOLD

Omp deep dish steering wheel £50
STEERING WHEEL PROVISIONALY SOLD

Eibach pro street coil overs fitted with gaz spring, very very stiff, good condition £250
COILOVERS PROVISIONALY SOLD

Alloy arms fitted with poly bushes £100

Whiteline roll centre adjuster kit £100
ROLL CENTRE KIT SOLD

Hdi fmic in black with pipes modified for rotated turbo and has welded boss for ait sensor. £150

V1 Sti interior, black with grey alcantra inserts wear on the drivers bolster but other wise good £150

My97 Catalunya shell fitted with, chargespeed front/rear bumpers, fibreglass wings, Abw wide arch extensions, poly bushed diff carrier, flat boot floor plus other bits. Shell really needs tidying up as it looks tatty and paint work is not very good, it has also been rewired using a loom from an my94 so uses a 4 plug Ecu. £750

Lateral built garrett GT3040 turbo, includes oil and water lines very little use £650
TURBO SOLD

4" blue silicon inlet and large RCM k&n filter with 4" trumpet £75
FILTER ETC SOLD

H&S rotated uppie and 3" down pipe, with turbo smart external wastegate and screamer pipe, wrapped but down pipe could do with re-wrapping, will be sold with 3" centre section and 2x back boxes 1 loud 1 quite system is slip jointed and all fits together. £650
UPPIPE/DOWN PIPE PROVISIONALY SOLD

cusco front under brace £35

All items exclude postage and PP fees, ill try and get some pics up asap but due to work requirements please give me time.
I will try and remove parts asap but again I work all week from 6am to 6pm most days so only really have weekends to do Anything, again please bear with me.

There are more bits and I will add them as I get time.

what turbo was you running?

wiley

A lateral built garrett GT3040 chap.

Hi
How much for the below please

-Phase 1.5 black inlet manifold including parallel rails, braided lines, turbo smart fpr, billet inlet manifold spacers,

Also a price without the inlet too please

1st dibs on the carnards, side skirts, grill and headlights please Ian.

i take it the turbo was rotated? If so im interested in the up-pipe, downpipe and wastegate, how much do ya need for them

How much for the fuel set up minus the 044 and warlbro?

Inlet and rails etc has been enquired about with full engine etc so is possibly spoken for, will let you know if not chap.

I haven't advertised the uppipe/down pipe yet mate as said at start of thread will advertise other bits when engine/gearbox has gone, but, the uppipe and down pipe will be advertised as a complete system inc centre section an back box for £600 as its all slip jointed.

As above for fuel system, it will be advertised as a package minus engine parts, ie rails etc, unsure in price at the mo, around £400 inc both pump, swirl pot, filter etc.

600 is gud for me u can put me down for the full system.

Hmm did you get my pm yesterday?

Sorry for the confusion chaps, I should have made things a bit clearer Iv got 3 or 4 threads running and trying to keep up with them, snake sorry I haven't returned your pm chap I was in the process of replying to them yesterday when my battery died on the i phone, I do apologise chap I missed yours, pm coming your way mate.
On the for sale thread for the whole car I'd said ill try and keep track of people's enquiries in the order they asked and get back to them if was certain I was breaking.
No bits will be removed from the car till the engine and box have sold so potential buyers can see them running, I again apologise for this but I'd rather be able to show buyers working items so they can be sure I'm genuine with what I'm selling, hope you understand guys.
I will merge all threads into one very soon to make it easier.
Gazney I'm afraid there are people before you for the rotated set up mate, again sorry for the confusion.

ENGINE NOW SOLD :(

Ok I don't know who you are gs67 but you obviously know me!!! My mrs name is becky so I'm assuming you know this?? Lets see if your brave enough to say this to my face!!!

GS67 is just a spammer mate posting random crap on different threads, i expect it'll be removed very shortly.

How would he know my mrs name mate? Must admit I am livid at the fact he has made a Personall attack at my other half.

Aside from the idiot, Iv added more parts :D some have had enquirers so ill let people know if they are available.

Where about are you? Interested in all the arb kit

Ian I will take the steering wheel will message you on FB for payment details.

Hi mate I'm in ipswich in Suffolk, I can post out parts fella.

What condition is it all in? How much do you think postage will be roughly? Ipswich is a bit of a trek

Do you have interior switch panel

Which panel are you after bud?

Sorry Ian....looking for switch panel .. fuel pump battery cut off etc

I haven't I'm afraid chap

Hi,

Do you have an A piller gauge pod and either EGT,water temp or any other gauges with senders/wiring
Regards
Neil

Hi mate, I don't I'm afraid just the set of defi's as advertised above.

Will the whiteline ARB's (front and rear) fit my 2004wrx?

If you could get some pics when you get a minute:thumb: I know your busy so no rush.:thumb:

Ab

Arbs have sold I'm afraid mate, will update list this evening as struggling with this poxy I phone lol.

List updated