HELP! maf sensor problem???!
Hi. i have a 1995 import wrx and a few weeks ago its started cutting out at junctions and when slowing down with clutch in. i changed fuel filter didnt help. so i got a second hand maf sensor (green label) i disconnected battery and fitted new sensor.left batery disconneted a while then tryed starting it. at first it ran ok but only for 10 seconds before cutting out.then after starting it a few times it ran but very lumpy after 2000 rpm and engine check light is now on. any help would be great.
|
I had the same symptoms as you (cutting out after 10secs-ish) when I forgot to replug the MAF sensor in after removing it temporarily so I'm guessing you're on the right track, perhaps it's the wrong type of sensor or not coneected properly??
|
Check the Idle control valve is working ok, was the MAF a new one? or a second hand one?
|
maf sensor was secound hand.my friend popped to garage to pick me one up. it has orange label instead of green.could i run it?how can i check icv?
|
Originally Posted by petebell
(Post 10964698)
maf sensor was secound hand.my friend popped to garage to pick me one up. it has orange label instead of green.could i run it?how can i check icv?
Re the ICV look at the link below for a pic of one, (it will be just below the intercooler on the right hand side,(mounted more centrally on later models try cleaning it with some brake cleaner, (do not remove it without a new seal as you will never get the old one back in).. All this is assuming your symptoms turn out to be the ICV ofc. I could be blowing up the wrong bagpipe so to speak. http://www.amazon.com/OES-Genuine-Co...KTNA%20target= Regards Dave. |
yeah i had a green label and got a second hand green label but presumed it was faulty my friend picked up orange label by mistake.were can i get part number for gasket as i cant find them any were!might help with the problem cheers
|
|
excellent found it cheers i disconnected positive from battery again going to leave a couple of hours see if it helps
|
ordered gasket. left the positive disconnected for over two hours to try reset ecu but still no luck?
|
Originally Posted by petebell
(Post 10965081)
ordered gasket. left the positive disconnected for over two hours to try reset ecu but still no luck?
|
yeah think ill just have to clean idle control and fit new gasket then try again.if that dont work new maf sensor and if that fails new idle control valve.
|
Originally Posted by petebell
(Post 10965081)
ordered gasket. left the positive disconnected for over two hours to try reset ecu but still no luck?
Originally Posted by petebell
(Post 10966445)
yeah think ill just have to clean idle control and fit new gasket then try again.if that dont work new maf sensor and if that fails new idle control valve.
|
Originally Posted by Ginola
(Post 10966437)
Have a look on here for a guide to reset it, on a newage you have to start/stop the engine 5 times, on earlier classics it will be different, there will be a guide on here somewhere.
To do a proper ECU reset on a stanard newage Denso ECU you need a laptop connected to the OBD II port with the necessary cable and software, there is no other way. Classics yeah you can do it - look on Jolly Green Monster's website. |
Originally Posted by MrNoisy
(Post 10966452)
FYI that doesn't reset the ECU on a newage it just clears certain CEL's if the problem's been resolved.
To do a proper ECU reset on a stanard newage Denso ECU you need a laptop connected to the OBD II port with the necessary cable and software, there is no other way. Classics yeah you can do it - look on Jolly Green Monster's website. |
took out idle control valve today and gave it a clean and fitted new gasket.now car wont start at all just keeps turning over?
|
Keep at it mate and it will start gradually, it may cut out a couple of times until it resets it self at the correct revs.
|
ok car started for a wole two seconds then cut out. it cuts out even if i keep the revs up?
|
Firstly pull up the codes for the ECU fault http://www.scoobypedia.co.uk/index.p...gECUCodes#toc3
Then reset the ECU http://www.scoobypedia.co.uk/index.p.../ECUReset#toc3 |
yeah ill try that tommorow morning.the guide i found said start engine but couldnt start it to check
|
You don't need to start the engine to check the codes, just turn the ignition on.
Good luck!! :) |
just did diagnostic test and is constantly flashin = no fault? must be a fault somewere gettin new maf tonight but not holding out much hope!
|
4 th maf sensor is here now with a airbox instead of induction kit.see if it helps
|
gasket on idle control valve was ok.car starts but doesnt idle and blows white smoke. just change idle control valve?
|
car only cuts out when the revs arent kept up its still showing no faults on diagnostic
|
Originally Posted by petebell
(Post 10970419)
gasket on idle control valve was ok.car starts but doesnt idle and blows white smoke. just change idle control valve?
|
car is not boosting at all now. no pipes have come off turbo. white smoke seems to have cleared?
|
ok took intercooler back off and the turbo is blowing air out intercooler pipe?its showing vaccum on my gauges of 50 kg/cm2? no oil showing in turbo. ordering a compression tester tonight
|
Dude, get a specialist to take a look,
Turbo's blow air that's what there designed to do.. |
engine gone it was blowing air from were was ment to be sucking,turbo is fine.looks like valves have gone putting air in cylinders and pushin out thru turbo creating a vaccum.new engine time :(
|
All times are GMT +1. The time now is 01:35 AM. |
© 2024 MH Sub I, LLC dba Internet Brands