front mount done at last!
 

hi all ,its done at last!!! :luxhello:
just finished fitting my front mount today, in total its taken around three and a half days! :cry:
think it looks good though , well worth the hassle!and all done for under £200 :thumb:
chris.:luxhello:

Nice mate, very nice:thumb:
Or good job, as a yank mate says:freak3:

Are you getting the map checked now it's on ??

great job, looks great.

soon :luxhello:, putting tdo5 on next :luxhello:, then remap , pals getting me mates rates on remap so getting as much done first! save in long run!:thumb:
cars not been in use for 5 mths just start it up every now and then , so doing bits to it first then mapping it once!:thumb:
chris.

Nice one! Like the carbon 'brows :)

cheers mate !:thumb: they cost enough, ( for what they are)
does make front look better imo
chris.

Yeah they do actually. Where did you get them from? When I eventually get a scoob I'd consider a set and I'm not usually a fan of brows on cars but these are carbon! Ha. I do love a bit of carbon.

when you getting one then??
my mate makes carbon bits so i get them cheaper ! :luxhello:
when you finally get a scoob let me know , he makes all sorts of stuff!
i was never a lover of brows either , but as you say carbon!!

chris.:thumb:

Oh wicked cheers chris :cool: well it's going to be this year with any luck. Insurance will be a bit steep but it's now or never. Need to sell my Alfa aswell to help raise funds for the car and insurance. But when I do I'll defo let you know :thumb: btw was your IC a kit or a home made job? I don't mean that In a bad way I mean did you buy all the piping separately then get an IC.

no mate not homemade, bought a hdi intercooler for £50 , first ,then bought a piping kit off e bay £ 135 , other bolts etc got from work
cheers chris .

Get some black mesh to cover/protect it, my type R has that, you cannot tell it has an FMIC fitted :D plus it stops all the stones hitting and damaging the FMIC.

Tony:D

Who's mapping it for you?

Looking good bud

one question, why not cut away that whole top part of the bumper you have drilled holes in, would cool better and look better and would still be rigid enough ?

Quite like the holes :) Tight fit in the garage, how do you get in and out, climb through the passenger window :D

Shaun

thought about it , just tried for a different look , :wonder: i like it now its fitted :luxhello:, plus my bumper got quite flimsy after all cutting:cry:
chris.

the holes are different ,i like them :) but wife says birds are going to nest in em ,:Suspiciou have to park it very close pass side!!!! then theirs just enough room to climb out
cheers chris.

hi mate getting it mapped through a friend , hes got a 480 bhp gt4 hes spent thousands on , mapper comes highly recomended by him:luxhello:
cheers chris.

But does he know SUBARUS?

If not, prepare for a big bill.............

Where did you get the black trim that uve got going around inside bumper by fmic?

its a boot seal mate , had one spare from a car i broke yrs ago:) fits well and stops bumper rubbing on intercooler:thumb:
chris.

I'm with Alcazar on this, if your mapper doesnt know Subaru's then dont get it mapped by them, it may well cost you a new engine :(

Tony:)

As already said above, make sure the mapper knows how to setup a Subaru otherwise it will cost you a good 3k to put it right! just because he can setup a GT4 really well it dont mean he can do a scooby;)

Looks good, bet you're itching to get it on the road:thumb:

looks really nice mate

mind straighten the steering before pushing it out lol

been off road for 5 mths now:cry: been doing odd jobs to her , taxing at end of month so i can have some fun:thumb:

thanks:thumb: yes its tight in my garage , more like a box room !
cheers all chris:thumb: