Bugeye Front Seats - Air Bag Light
Hi all
i have just changed the front seats but my old seats had the air bags in. I have fitted the resistor 3.3 on both sides but air bag light is on. should have i disconnected the battery first :wonder: becuase i didnt. Whats the solution without taking the buld out. is it a simple ecu reset regards Colin |
Originally Posted by Modifications
(Post 10181303)
Hi all
i have just changed the front seats but my old seats had the air bags in. I have fitted the resistor 3.3 on both sides but air bag light is on. should have i disconnected the battery first :wonder: becuase i didnt. Whats the solution without taking the buld out. is it a simple ecu reset regards Colin |
ok i will try that :-) or get it reset if it doesnt work :-)
cheers buddy |
Originally Posted by Modifications
(Post 10181303)
Hi all
i have just changed the front seats but my old seats had the air bags in. I have fitted the resistor 3.3 on both sides but air bag light is on. should have i disconnected the battery first :wonder: becuase i didnt. Whats the solution without taking the buld out. is it a simple ecu reset regards Colin Can you point me in the direction of where you got your resistor, i've changed the seats in my bug for ones form a P1 and have the airbag light up. |
Originally Posted by 95turbowagon
(Post 10181466)
Can you point me in the direction of where you got your resistor, i've changed the seats in my bug for ones form a P1 and have the airbag light up.
Maplins m8, couple of quid each.. |
Originally Posted by Modifications
(Post 10181303)
Hi all
i have just changed the front seats but my old seats had the air bags in. I have fitted the resistor 3.3 on both sides but air bag light is on. should have i disconnected the battery first :wonder: becuase i didnt. Whats the solution without taking the buld out. is it a simple ecu reset regards Colin |
I took mine out and fitted the resistors, didn't disconnect the battery and the light went out fine. Same with my steering wheel and passenger airbag - if the resistors are making a good connection they should go straight out:wonder:
|
Originally Posted by JonMc
(Post 10181487)
I took mine out and fitted the resistors, didn't disconnect the battery and the light went out fine. Same with my steering wheel and passenger airbag - if the resistors are making a good connection they should go straight out:wonder:
Hope u have better luck than me m8:thumb: |
95turbowagon
hi m8 i used 3 x 10k resistors and twisted them together to get the 3.3K. i have loads spare if you need some. madmerlin my cousin has the snap on jobby, so i will get it reset with that... i have used it loads of times with all the scoobs i have had otherwise i need SY |
Originally Posted by JonMc
(Post 10181487)
I took mine out and fitted the resistors, didn't disconnect the battery and the light went out fine. Same with my steering wheel and passenger airbag - if the resistors are making a good connection they should go straight out:wonder:
what resistors did you use m8, if you dont mind me asking ( 3.3k 0.6W ) |
Originally Posted by Modifications
(Post 10181499)
i soldered them :brickwall
|
errmm strange i will get an ecu reset and see how it goes
|
Just in case you have wrong resistors it is 3.3ohm not 3.3k resistors and nothing should need resetting once the airbag ecu sees 3.3 ohm it will extinguish the light, I did same in my wrx, but the resistors being thin wires needed the wires folding to increase dia before pushing in the plug to make a good connection, I would say either wrong resistors or bad connection in plug
|
Originally Posted by Modifications
(Post 10181499)
what resistors did you use m8, if you dont mind me asking ( 3.3k 0.6W )
|
hi Daz
they have been soldered so its not bad connection i have fitted 10k x 3 twisted together which should give 3.3K, do you have a part number? or a link? |
Originally Posted by JonMc
(Post 10181569)
3.3ohm, 0.25w; I've given some to a couple of mates around here and they've not come back reporting any issues:wonder:
:thumb: |
|
Originally Posted by Modifications
(Post 10181586)
do you have any spare or a link we the buy them from
:thumb:
Originally Posted by Modifications
(Post 10181583)
hi Daz
they have been soldered so its not bad connection i have fitted 10k x 3 twisted together which should give 3.3K, do you have a part number? or a link? |
ok m8 cheers, dont mind paying
|
Originally Posted by Modifications
(Post 10181591)
|
i will order these then m8, but thanks such much
|
Originally Posted by Modifications
(Post 10181597)
ok m8 cheers, dont mind paying
|
Hi Mate,
I had the same problem as you in mine...i did post the issue and the "fix" in May.... -------------------------------------------------------------------------------- Resolution to this problem is as follows: 2 x 3.3ohm 0.6w resistor from Maplin's for 21p each (one for each seat.) Place one in each clip underneath the seat.....voila...airbag light now off...!! The resistors do need a good connection though. |
Can I jump on here please, my airbag light was on when I bought the car and he did say he changed the front seats....where does the resistor go? is it something to do with the yellow plug under the seats? cheers lads
|
Originally Posted by leeturbo2000
(Post 10181612)
Can I jump on here please, my airbag light was on when I bought the car and he did say he changed the front seats....where does the resistor go? is it something to do with the yellow plug under the seats? cheers lads
|
yes Lee it is m8,
i just ordered 10 off so got some spare if you need. i removed the plastic surrounds then soldered the wrong resistors to the base of the crimps lol. but got the correct ones coming now so if you need some let me know :-) Thanks JonMC, ebay has some coming in the post just hope they work LOL |
Originally Posted by JonMc
(Post 10181619)
Yes, you need to bridge the terminals with 3.3ohm resistor and the light will operate as though the airbag is in-situ:thumb:
|
Originally Posted by Modifications
(Post 10181622)
yes Lee it is m8,
i just ordered 10 off so got some spare if you need. i removed the plastic surrounds then soldered the wrong resistors to the base of the crimps lol. but got the correct ones coming now so if you need some let me know :-) Thanks JonMC, ebay has som coming in the post just hope they work LOL :thumb: |
sorry i did miss that i fitted 3.3K and not 3.3R shiiiiiiiiiiiiiiite
|
Originally Posted by leeturbo2000
(Post 10181631)
Cheers mate that would be great! I owe you a pint also
:thumb: |
All times are GMT +1. The time now is 03:15 PM. |
© 2024 MH Sub I, LLC dba Internet Brands