2.1 10sec DIY Drag Monster..
Well I've finally found the time to put up a project thread on my latest car - the objective a 600bhp + 10sec road legal drag car, the base being a GC8 STI 4 saloon..
I've already collected the following from Lateral Performance:- -Custom Wiseco stroker pistons -Crower/Lateral H-section Rod set -EJ257 79mm Crank -EJ20 Closed deck block (rear thrust converted,rebored) -ACL Race bearings -1.6mm Headgaskets -Cosworth 11mm ultra high performance head studs -Cosworth kevlar cambelt -11mm high flow oil pump -Cosworth Sump baffle -Complete engine gasket set -RCM rotated turbo kit -Garrette GT35r 0.82AR with custom ported shroud -Tial external wastegate -Exedy Hyper Twin D-core clutch -3 bolt Headers -Solaris Syvecs S6 PNP, 3 bar map sensor, 3port solenoid -Fuel labs FPR -Fuel lab Billet filter Parts I have sourced elsewhere : -JUN titanium retainers -JUN Valve springs -Supertech Inconel valves -Piper Custom spec 276 camshafts -Hybrid FMIC -Carl davey Modified reversed intake manifold - This has been heavily ported Headwise a friend of mine who builds and races high spec VW's with over 10 years porting experiance has very kindly knife edge ported and gas flowed the V4 heads to a very high standard, he has also 3 angle cut the valve seats, lapped in some shiny new Supertech Inconel valves, and shimmed up the clearances to suit the custom piper 276 cams I picked up a PPG straightcut box on here with billet selector forks complete with R180 rear diff and DCCD center diff at a decent price from a member on here so that sorts the transmission out out for now - I know this won't last long however im fully prepared to fork out on 6 speeder when required. Fuelling wise I have yet to buy some decent billet fuel rails, 2 x Bosch 044 pumps and a swirl pot Whilst there is no engine in the car, Im thinking of stripping all the unwanted sound deadening, carpet, trim etc I've got loads of pics of the engine build in progress, head porting etc and will try and get them up as soon as I can |
ohh this should be good :D
|
Good on you Omar. This is going to inspire me even more & i cant wait till you introduce it to everyone on the strip :lol1:.
Looking forward to the pictures. |
Looks a cracking build spec Omar, be good to see you at Shakey and welcome you to the 10 second club.
|
very nice spec list, I like it!
Simon |
very nice spec list, I like it!
Simon |
Originally Posted by MartynJ
(Post 9503975)
Looks a cracking build spec Omar, be good to see you at Shakey and welcome you to the 10 second club.
|
Originally Posted by Jolly Green Monster
(Post 9503979)
very nice spec list, I like it!
Simon |
Originally Posted by 786omar
(Post 9503988)
Looking foward to it Martyn :) Hows your car coming along?
Very nicely thanks, 5 more 10 second passes so far this year and nitrous being fitted this week for the weekend round. |
Wondered what was going on with yours today Martyn. Cracking build Omar! Subscribed.
|
Nice shopping list :)
Sounds like it's going to be a good one fella. All the best :thumb: |
Good stuff Omar, now hurry up and get those pics up :D :thumb:
Banny |
Will be watching this one.
|
Sounds very interesting, 'll watch it
|
Only thing I would change is the 3 bar map sensor as that is only good to 2 bar gauge pressure, so a 4 bar would allow the 2.2bar that you'll probably want to run, with headroom and proper overboost fuel cut. I would add a NTK wideband sensor too.
Looks good so far. |
Paul it may even be 4 bar sensor I'll double check the invoice tonight if it isn't I'm sure mark will swap it over for me :) as for the NTK wideband kit I'll need you to supply that when you come down to set up the base map
|
Originally Posted by ZEN Performance
(Post 9504656)
Only thing I would change is the 3 bar map sensor as that is only good to 2 bar gauge pressure, so a 4 bar would allow the 2.2bar that you'll probably want to run, with headroom and proper overboost fuel cut. I would add a NTK wideband sensor too.
Looks good so far. There are loads you can are onto the list for the Syvecs;) |
sounds very interesting!!!!
|
Another nice looking build, let's see some photos fella
|
Look forward to seeing this complete... good luck with the project Omar :thumb:
|
just seen some of the pics and i dont know why omer aint sharing them :norty:
|
Originally Posted by banny sti
(Post 9504558)
Good stuff Omar, now hurry up and get those pics up :D :thumb:
Banny |
A few teaser pics which I took from my phone :) proper pics yet to be uploaded
http://i173.photobucket.com/albums/w...R/fe51a798.jpg http://i173.photobucket.com/albums/w...R/99a6ec82.jpg http://i173.photobucket.com/albums/w...R/e0ee7b35.jpg |
Wicked :thumb:
|
loving the pics mate,i cant tell you how it looks like what ive got on the go with mine except ive got scdb and eagle rods,and i love forge pistons there pure porn:D
|
Originally Posted by Anger
(Post 9505620)
Look forward to seeing this complete... good luck with the project Omar :thumb:
Thanks what happened to your RA ? Any plans for the newage? |
Originally Posted by Mad Hammer
(Post 9505614)
Another nice looking build, let's see some photos fella
|
very interesting project. i will be watchig his one :thumb:
ps, nice rug lol |
Originally Posted by 786omar
(Post 9505934)
Thanks, I don't know if you remember but I'm the same person that bought the r180 diff from you a few years back when your car was being built at zen
|
Lol thanks I was waiting for someone to comment on the rug, still not as bad as banny's legendary carpet! That's some serious spec car you got there didn't it have a T04Z on there at one point ?
|
All times are GMT +1. The time now is 02:09 AM. |
© 2024 MH Sub I, LLC dba Internet Brands