that looks mint last pic
|
|
Where did you's get the Defi Gnomes from?
|
always sets for sale on ebay.....
sold mine recently in favour of the BF range of defis with the warning sounds.. :thumb::thumb: |
3 Attachment(s)
Blitz Mirror drives in a carbon pod, and an AEM wideband on the A pilar:
Attachment 53586 Attachment 53587 Attachment 53588 |
Wow saint where did u get that pod? I want one!! where do they sell it? :thumb:
Here are my defi gauges http://lh4.ggpht.com/_pF1owX8GFmg/Sk...EPLI%20110.jpg |
Originally Posted by monkeyboy173
(Post 9114470)
Heres mine. Defi Oil Press, Oil Temp, Boost & Knock Link in a triple pod. Then Defi Water Temp in the air vent & Stack Wideband Lambda in a pod.
http://i4.photobucket.com/albums/y14...16/Gauges1.jpg http://i4.photobucket.com/albums/y14...16/Gauges2.jpg |
I've done mine in an arc around the fuel pressure gauge.
It's not easy, some nice soldering;) DO use plenty of cable, it's best tucked up rather than fiddling trying to get it to fit if it's too short;) I wrapped all mine in non-sticky loom tape to make a nice job. Oh, and when removing the LEDs from the board, CLIP the legs, one long, one short, for identification afterwards, and the legs left sticking out of the board are easier to solder to than trying to get wires back through the board. I used small shrink fit tubing as an insulator. |
Originally Posted by Mayrun
(Post 9209526)
Wow saint where did u get that pod? I want one!! where do they sell it? :thumb:
|
Hi guys anyone know where to run the green wire from my 2 in 1 boost and rev counter gauge I have done the boost one but dont know where to connect the green wire from the rev counter instructions say it needs to be connected to the negative wire from the coil. I have been told this is traceable from the ECU but there are loads of wires any one know which one it is??
|
1 Attachment(s)
not the best pics but
DEFI - oil temp, oil pressure, EGT in the centre pod DEFI - fuel pressure, water temp on the left HKS large display boost gauge 2.5bar on the right Attachment 53591 steve |
Originally Posted by Saint AAI
(Post 9213027)
It's a Kakumei and I got it from, dare I say it, Flat4Online :eek:. Comes with 52mm or 60mm holes. Probably easily available from elsewhere, but in Flat4's defence it came promptly, as has everything I've ordered from them. Maybe I've just been lucky.
KAKUMEI 96-00 IMPREZA GC8 100% CARBON GAUGE POD (52mm) : eBay Motors (item 270055956018 end time Feb-28-10 09:17:07 PST) I really want it, my fiber pod has already few scratches on it :cry: |
Originally Posted by alcazar
(Post 9210959)
I've done mine in an arc around the fuel pressure gauge.
It's not easy, some nice soldering;) DO use plenty of cable, it's best tucked up rather than fiddling trying to get it to fit if it's too short;) I wrapped all mine in non-sticky loom tape to make a nice job. Oh, and when removing the LEDs from the board, CLIP the legs, one long, one short, for identification afterwards, and the legs left sticking out of the board are easier to solder to than trying to get wires back through the board. I used small shrink fit tubing as an insulator. |
2 Attachment(s)
Old setup.
Attachment 53575 New setup Attachment 53576 Also have a KS3 hidden away, warning led is remote mounted into the carbon dash surround. |
Originally Posted by Luckyscoob
(Post 9110736)
Just had these fitted. Prosport steppers in amber.
http://i12.photobucket.com/albums/a2.../Gauges005.jpg http://i12.photobucket.com/albums/a2.../Gauges003.jpg Ralph |
1 Attachment(s)
|
Originally Posted by ScoobyRalph
(Post 9235865)
What paint did you use to get the match and where can you buy it??
Ralph Went to halfords. Its a peugeot cossack grey met. :thumb: |
Nice one luckyscoob!
Cheers Ralph |
Originally Posted by dazdavies
(Post 9133478)
Here's some of my 60mm Blitz Mirror Drive Gauges. Notice the matching blue dash lights ;)
http://www.scoob.co.uk/typer/blitzgauges/4.jpg http://www.scoob.co.uk/typer/blitzgauges/5.jpg http://www.scoob.co.uk/typer/blitzgauges/6.jpg http://www.scoob.co.uk/typer/blitzgauges/7.jpg |
I've an unused Newage 3 gauge pillar pod for sale if anyones interested 52mm.
Ricey |
Originally Posted by Rice Rocket
(Post 9254586)
I've an unused Newage 3 gauge pillar pod for sale if anyones interested 52mm.
Ricey |
1 Attachment(s)
|
Originally Posted by slipstream_uk
(Post 9133705)
http://i726.photobucket.com/albums/w...r/SANY0005.jpg
http://i726.photobucket.com/albums/w...d/SNC11028.jpg http://i726.photobucket.com/albums/w...1040Medium.jpg |
Ours. Defi racer blue BF's
http://img.photobucket.com/albums/v6...1/Cen_Cons.jpg |
mmmmmmm, defi's!!! one day..............
|
I've got Defis waiting to go in, just not spent the cash on an ATI triple pod yet £140, think it was £80 last year:cry:
|
Just ordered another gauge for Fuel Pressure yesterday so had to make space for an extra gauge on the dash last night.... Quite happy but pics will have to wait until the dash is back in :D
|
4x Defi Amber BF's: 3 pod (RCMS) - Oil Temp, Pressure & Boost. Fuel Pressure in Drivers vent.
Knocklink in main dash, defi controller in cupholder and inlet temp in space next to it. http://i53.photobucket.com/albums/g6...r/DSCN4409.jpg http://i53.photobucket.com/albums/g6...r/DSCN4410.jpg http://i53.photobucket.com/albums/g6...r/DSCN4412.jpg http://i53.photobucket.com/albums/g6...r/DSCN4414.jpg http://i53.photobucket.com/albums/g6...r/DSCN4420.jpg |
very tidy!!! ;)
|
Anyone recommend a good quality A pillar gauge for 2 prosport gauges. I see most seem to favour 3 gauges in centre pod but I really like the A pillar pods but there dont seem to be much choice over them??
|
All times are GMT +1. The time now is 10:47 PM. |
© 2024 MH Sub I, LLC dba Internet Brands