New 2dr wide arch sprint/hillclimb car build
6 Attachment(s)
Its time to retire the old 4dr gold scoob from competition after 3 great years,numerous class victories. 2 championships won Nottingham sports car club 2008 and Liverpool and chester speed championship 2009.With 5 class records took this year,its bye bye old car hello new car.
Its being based on a prodrive stock 2dr shell.Custom cages T45 weld in cage,carbon roof with built in vortex generators,carbon kevlar front 22b wings,carbon kevlar 22b rear 1/4,carbon boot,boot floor removed,RCM 22b rear spoiler,RCM sequential gearbox tunnel buldge. Attachment 53473[/IMG] Attachment 53474[/IMG] Attachment 53475[/IMG] Attachment 53476[/IMG] Attachment 53477[/IMG] Attachment 53478[/IMG] |
2 Attachment(s)
The shell is fully seam welded with strengthened strut tops,fully firewalled.Its going to run a 22b replica front bumper with carbon fog covers,rear defuser with flat floor front to rear.It has full WRC rear cross member and anti roll bar mounts,it will run a modified standard rear cross member for now though.It doesn't have the rear spoiler or bonnet and rcm scoop on now as in the first picture as these are not mine.It has full welded in seat mounts and comp battery box fitted for a oddessey battery.Its going to run twin bosch 8bar 200ltr fuel pumps.
Attachment 53479[/IMG] Attachment 53480[/IMG] |
2 Attachment(s)
|
should be hellish, keepin my eye one this one :D
|
very nice , get some paint on that bare metal :D
|
Great stuff!! :)
|
Loojks fantastic- some work going on there!
|
Originally Posted by ABW
(Post 9072860)
very nice , get some paint on that bare metal :D
|
Originally Posted by CRonson7
(Post 9072811)
should be hellish, keepin my eye one this one :D
|
that garage and cars........ your my idle lol
|
Excellent stuff. Can I ask how you heard about and secured the shell?
I shall be following this with great interest. |
Originally Posted by philS scooby
(Post 9074232)
that garage and cars........ your my idle lol
Originally Posted by dazdavies
(Post 9074243)
Excellent stuff. Can I ask how you heard about and secured the shell?
I shall be following this with great interest. |
[QUOTE=wrxbart;9074925]LOL i only wish it was my garage,mines the dark cramped one:lol:
you could move it to that big garage you have lol but then again that could spell the end of your marage think i need to come down and see this in the flesh or better still stay away so i dont get any ideas |
This is going to be mental.Fair play to you I cant wait to watch this build
|
this is going 2 be great............
|
Originally Posted by yellowevo
(Post 9075593)
This is going to be mental.Fair play to you I cant wait to watch this build
Originally Posted by brockalightus
(Post 9075843)
this is going 2 be great............
|
That looks like it'll be a bit naughty!!!!
|
The engine for this is my old one out of the gold scoob, but with a few more mods.
Its a ej22 closed deck block with piston oil squirters,bored out 40thou with wisco pistons and manley rods. Ej257 crank machined for centre thrust acl race bearings,12mm modified oil pump with cosworth baffle plate. 11mm arp head studs which are going to be replaced with 14mm ones,cometic gaskets with avcs heads (maybe ported yet as well). Inlet manifold to be decided yet either my phase 1 reversed but widened to fit or a 2001 bugeye reversed one with aps 8 injecter setup? Gt spec gen2 headers with twisted turbo setup running at the mo a gt35 with .63 housing but hopefully it will have a tial .82 stainless housing. RCM filter and aluminium inlet,race fuel cell with 2 bosch 8bar 200ltr pumps. Side exit exhaust system, Solaris ecu mapped by simon of cause (JGM). Oh and a 75 shot of nos hopefully to finish. The aim of 600+ on pump and 660 on race then the nos on top |
Brakes are brembos all round with standard discs and pads rear and DBA 2 piece front discs and carbotec xp8 pads. Bias non servo pedal box and hydrualic hand brake.HEL braided pipes.
|
Looking forward to this one. Best of luck with the build :thumb:
|
Loving that cage.... any more pics of how it fits around the dash?
Looking forward to seeing this develop. |
Originally Posted by rossi_p
(Post 9076391)
Loving that cage.... any more pics of how it fits around the dash?
Looking forward to seeing this develop. |
Theres a thread on 22b about Cosworth 11mm headstuds that might be of interest to you before you start modifying the block to take 14mm ones
|
Originally Posted by Jay m A
(Post 9078736)
Theres a thread on 22b about Cosworth 11mm headstuds that might be of interest to you before you start modifying the block to take 14mm ones
|
subscribed :)
|
looks like its gonna be a goodn :thumb:
|
Very nice project, fantastic job. cong.
Where do you buy 22B Body ? HT Autos ?? |
Originally Posted by UGUR YUMAK
(Post 9086287)
Very nice project, fantastic job. cong.
Where do you buy 22B Body ? HT Autos ?? |
Originally Posted by wrxbart
(Post 9087256)
Hi mate no they were not from ht autos,moulds were made from original 22b panels then the panels were made in carbon fibre.The moulds are owned by a friend and i can get them made for you if needed.
How much ?? |
Will get ya a price,do you want carbon/kevlar or fiber glass mate
|
All times are GMT +1. The time now is 12:23 PM. |
© 2024 MH Sub I, LLC dba Internet Brands