ScoobyNet.com - Subaru Enthusiast Forum

ScoobyNet.com - Subaru Enthusiast Forum (https://www.scoobynet.com/)
-   General Technical (https://www.scoobynet.com/general-technical-10/)
-   -   arggggggggghhhhhhh (https://www.scoobynet.com/general-technical-10/734247-arggggggggghhhhhhh.html)

jasongtr 27 December 2008 08:37 PM

arggggggggghhhhhhh
 
in the process of getting my engine out and at the point of unbolting the downpipe from the turbo - go to unbolt the middle section from it and what do i find.......


the whole bloody exhaust is welded up in one piece..... so now ill have to cut it off and buy a new exhaust (might aswell get stainless headers too:norty: )

why is nothing ever easy?

RON 27 December 2008 08:40 PM

Can you not just remove it in the one piece, and then refit it...?? it's not like they go over the axle on the scoobs....

jasongtr 27 December 2008 08:44 PM

doubt i could get the whole car up high enough, dont really want to buy a new exhaust as its going to be a donor car for a murtaya build but my plan was to rebuild the bottom end/new 2.5 one and get her back on the road for a while - the other option would be to just break the car now

RON 27 December 2008 08:48 PM

it doesn't need to be that high if you're taking the engine out...

jasongtr 27 December 2008 08:51 PM

surley it would nee to be as high as the length of the downpipe?

RON 27 December 2008 09:00 PM

the down pipe only needs to be disconnectedfrom the turbo, and lowered a bit, doesn't need to be right out to get the engine out, maybe if you're taking gearbox aswell....

jasongtr 27 December 2008 09:04 PM

ok i understand now, no not taking the gearbox out yet, turbo has one more bolt that looks a pig to remove, the only other thing that looks intersting is spliting the engine and box, the guide i have says you need to thread a 6mm bolt in somewhere (maybe something to do with the clutch arm?)

RON 27 December 2008 09:11 PM

yeh, once you have the starter removed, there is an allen headed bolt visible, remove that, and behind it is the clutch arm pivot, you need to find a bolt to thread into that, and pull it out, then, you need to jiggle the clutch arm, which you can do by holding onto it where the slave cylinder pushes it..... then, once you've got it all unbolted, it'll be a swine to get them apart, you may need to wedge bars and screwdrivers etc into the joint, make sure to do it squarely..... it might take quite a while to get it apart, mine took about a day the first time, and it was only 5 yrs old at the time...!!!

Good luck!

jasongtr 27 December 2008 09:25 PM

the find a bolt bit (wont one i have taken off so far work, if not what size i think ive seen its M6 but how long) also you say thread it in then pull it out, what do i oull out the bolt i have just threaded in or the arm itself?

RON 27 December 2008 09:28 PM

i just find any old bolt that will go in enough to pull the arm out, when you get to do it, it'll become clear..... esp once you've got the box out and can have a proper look....

jasongtr 27 December 2008 09:34 PM

so i thread a bolt into the arm and that releases it so it can be removed?

RON 27 December 2008 09:51 PM

thread the bolt in, and then pull the entire arm out...... it's about an inch or so in diameter, and about 150mm long..... it might be a bit tight if it's not been out before.... and when you come to putting it back, there's a big slot in the other end that has to be located to get it right... all will become obvious when it's out....

jasongtr 27 December 2008 10:07 PM

ok cheers ron, ill have a pop tomorrow

johnnybon 28 December 2008 01:06 PM

your right
 
why is nothing ever easy?[/quote]

Your right :) but if it was easy we all would be machanics:)

jasongtr 28 December 2008 08:39 PM

engine all ready to come out tomorrow (if the clutch thing has released properly) having the downpipe/cat still there made getting the gearbox/engine bolt out a real PITA, anyway hoist (new one) all built up so should be out in an hour or so tomorrow (engine and box seperated by about 10mm so i know that wont be a problem splitting it)

Jolly Green Monster 28 December 2008 09:44 PM


Originally Posted by jasongtr (Post 8378418)
if the clutch thing has released properly)

did you pull the release fork pivot right out???

Simon

jasongtr 28 December 2008 10:37 PM

er no is it supposed to come out the top completely, didnt think itwould come out completely???

Jolly Green Monster 29 December 2008 09:37 AM

the pivot not the fork

you remove the 10mm allen bolt and then put a bolt into the hole and into the thread on the end of the pivot.. the cambelt cover bolts are the right size.. then pull the pivo out whilst wiggling the fork.

Simon

jasongtr 29 December 2008 09:39 AM

ok thanks that bits done already, just about to go out and take the lump out now


All times are GMT +1. The time now is 02:10 PM.


© 2024 MH Sub I, LLC dba Internet Brands