Lets see your nuts
 

Lets see your nuts....wheelnuts that is... ;)

Not standard ones like this :o :

http://i2.photobucket.com/albums/y4/...B/CIMG1091.jpg

Oh all right :D

Rays EXTENDED

Cheers BOB5 :thumb:

http://img.photobucket.com/albums/v2...y/RAYSnuts.jpg

Rays EXTENDED ;)

http://i166.photobucket.com/albums/u105/BMGC/caps4.jpg

Have some Tuner Ultralites en route so will post them up:thumb:

I'll post a better pic later. this one deleted!!

STI Nuts

http://i18.photobucket.com/albums/b1...7/P1010146.jpg

http://i18.photobucket.com/albums/b1...6/P1000657.jpg

Frayz, I think you need to sort your centre caps out. they dont match the rest of the wheel colour ;)

Where can I get hold of these?
I am looking for some black ones to match my new wheels
How come one of your centre caps is silver and the other one black?
:)

Thats how they came mate... ive got some the gold ones but prefer my silver ones.

Guys, where did you buy the Rays wheels nuts and how much where they?
Are they aluminium?
Cheers :)

Those look great IMO mate :thumb:

I got mine from Unit8

Try here, there cheaper

Rays Engineering - Racing DURA NUTS - Nengun Performance

From here:

https://www.scoobynet.com/group-buys...-water-10.html :thumb:

Might fit some black ones to mine. Need some nice wheels to go with them too though :(

mine :D (RAYS Short)
http://img.photobucket.com/albums/v6.../aDSC00199.jpg

One is of the original cap, the other is when I made some black ones up to compliment the Black nuts

STI Wheel Nut Set (Black) ST28170ST020

I got mine from the USA, Edo Performance.
these cost me about £150 i think they RRP about £200


Not sure where the other guys bought their RAYs nuts but I have used this site in the past for a lot of stuff: -

Question for all the guys with Rays nuts.

Have any of you had problems with the nuts discolouring? I have had mine on for 2 years now but within the first year they discoloured from Blue to a patchy White:wonder:. I don't use any solvent cleaners on the wheels just hot soapy water and a soft bristle brush

You can just make it out in the pic below all four wheels have the same problem.
http://i158.photobucket.com/albums/t...March011-1.jpg

Trails did a GB on here last month from BOB'5, thats were i got mine from. I think he still has some left, Link
Dunno about discolouring because i've only had them on a few weeks!!!

My nuts all soapy

http://i74.photobucket.com/albums/i2...i/DSCF0205.jpg

They are just cheapos in comparison with the fancy dans on here ;)

scotthdlr- Ive only just put mine on in the last few weeks so cant comment, i hope they dont discolour too much

Will short nuts be OK for these alloys?
They are prodrive GT1 ones.
http://img.photobucket.com/albums/v617/feb/567841-3.jpg
http://img.photobucket.com/albums/v617/feb/567841-1.jpg
Please let me know as I need to order soon!
Cheers :)

Wheels loog good! Short should be fine i think

You know me, I like to show my nuts off

http://i18.photobucket.com/albums/b1...ren-/nuts1.jpg

I use OEM nuts for the winter and these babies for the summer

http://i18.photobucket.com/albums/b1...-/890b91d1.jpg

http://i18.photobucket.com/albums/b1...gardlugs11.jpg

http://i18.photobucket.com/albums/b1...uGardLug22.jpg

Mugard Spline lug nuts...the best!

You have the same nuts as me scoobymad ooo errr :lol1:

:luvlove:

Yes, but I would go for a small edge on the 60 deg tapper if I were you. OEM wheels tend to have a shorter seat.

http://www.revolution247.com/images/...TURNER-200.gif

I just ordered these from Keith @ Revolution and they are internal drive to protect the shaft:thumb:

I am not sure what you mean by 'small edge on the 60 degree tapper' :confused: Do you think the Rays ones will be a bit too wide for the OE wheels then?
The only potential problem with the above is that it needs a 12mm allen key whereas the 'standard' Ultralite External Nut (first on top of page: Revolution) looks more like the OE ones.
How come these are so much cheaper than the Rays ones?


Cheers :)

£££ Because they are Rays ! ;)

They come with the internal drive key ;)

Rays would fit fine. Look at your OEM nuts and you will see a shorter 60 degree taper.

Longer in a shorter is fine but shorter in a longer can carve up the wheel seat depending on the nut.

For example Frayz's speedline wheels come with shorter taper nuts for the speedline fitment, but the Rays work fine :thumb:

Yes ooo errr :D

Did you get yours from the US of A? I got mine from SubyDude in the US.