I cant find the thread that had the brake disc fitting instructions for the Mk1 (MY00)...

My search doesnt seem to find it..

anyone help?

What sort of instructions are you looking for? How to? Or what fits what?
Alcazar

how to mate.

wheel off
caliper off
remove 2 small philip screws
& pull :D

2 small philips screws, where are they, werent on my discs ?

Nor mine. Just pulls off once the calliper is removed.

Andy

it was a while ago since i did it but im sure there were 2 little screws holding it on , if there isnt then its going to be even easier :D

must be getting confused with my old shed of a rover :D:D it is hot u know

dont forget to loosen the resorvoir for the brake fluid

its a closed system and many people forget and fill the dam thing up which is a pain..

hmm...

Ive fitted plenty of discs to other cars.....so i guess its just run of the mill stuff..

It is pretty run of the mill stuff but this months Japanese performance has a detailed how to on uprating brakes on the Impreza...

Trust me - dont let the disk drop on your foot !

T.

Full instructions in True Grip vol4 issue1 Dec 2001

Sorry if some of this is a bit basic!

Please read the whole procedure before beginning!!!!

I take it you can jack the car? OK, just incase!
Use the jack from the boot the handle is clipped under the wooden floor (above the spare wheel)! (I know people that have not found this in 3 years of ownership).

Place the jack behind the front wheel. If you look at the sill there is a cut out in the plastic sill cover.
There is a groove in the top of the jack, it fits the part of the sill sticking down.
Remember to loosen (not remove!!!) the wheel nut before you take the weight off the wheels (1 turn will do).

Take the wheel off.
There should be 2 pins on the calliper (nearest to the front of the car). Follow the pins inboard (towards the engine) past the curly clip to the other side of the calliper. There should be a wire type clip that goes through the pins and clips into the calliper in between the pins.
Remove the clip (noting how the clip goes). (It's spring steel so will bend a bit if you need to).
Note the way the curly clip goes round the pins.
Withdraw the pins (you may need a pair of pliers) be careful of the curly clip it may spring off!!
Don’t worry if the disk feels loose as the wheel holds it on usually!!!
With the pins removed you should be able to pull the pads out (you may need pliers) (If they don't come out give them a bit of a wiggle or try to push them back in to the calliper with a large flat screwdriver).
Once you have the pads out you need to push the Pistons (pots) back in (do not damage the rubber dust seal round the pistons). A G clamp is ideal or a piece of wood/screwdriver.
It can be a bit awkward as the other pistons sometimes move out when you push one back (It's a bit of trial and error until they are all pushed back enough to get the pads in). Just do each one a bit in turn and then go back round.
It's not as difficult as it sounds!!!

Now unbolt the calliper from the hub (these bolts will be very tight!! Make sure you use the correct size socket (you do not want to round these buggers off!!))
With the calliper removed the disk should come off if it doesn't give it a tap from behind with a mallet:)
Clean up the mounting surface of the hub. Apply a little Copper grease to the surface of the hub (should stop it seizing on again)
Put new disk in place and bolt the calliper back on.
Clean both sides of the disk with brake cleaner.

Take the new pads and swap all the anti squeal shims over from the old pads. (Do not get any oil/grease or other muck on the disk side of the new pads!!!)
If you have any Copper grease smear a little on the shims before you refit the pads.
Now put the new pads in to the calliper and put the pins through. (If they don't fit you may have to push the pistons back a bit more) Do not damage the new disk!!!!!!

Now put the curly clip on to the pins (the same way up as you should have noted before removing it). If it won't fit, remove 1 of the pins half way, and push it through the clip and then push it all the way home.
Re-fit the wire clip (you may have to turn the pins so the holes in the pin line up with the clip).
Re-fit the wheel. Do the bolts up finger tight.
Lower the car.
Tighten the wheel nuts fully (It is good practice not to tighten them in order. Do them up in the sequence---1,3,5,2,4) (1 is any nut!! It's just your starting point). This makes sure the wheel goes on straight. This method should be used with any wheel, regardless of car manufacturer.
Start the car and depress the pedal fully, pump the pedal until the resistance returns.
The car should now be safe to drive, but to make sure take a gentle drive down a quite street and test the brakes.
Please be aware that new pads/disks will require bedding in (please see manufacturers instructions).
I take no responsibility for anyone following these instructions. If you are not confident after reading this please take seek professional help ;)


It is your responsibility to find out the correct torque for all the bolts!!