Version 1 replacing intake Resonator box
This is my current intake system setup.
https://cimg0.ibsrv.net/gimg/www.sco...d5d8c3c1cf.jpg Now i know you can get Apexi resonator deletes but i tried this and i didnt like the angle the air filter was at, with my current setup the air filter gets direct cold air from above the headlight (with the bonnet brow rubber removed) Now, i want to remove the plastic resonator box but still keep the current angle/setup of the air filter. ive done some measuring and the maf/90 degree elbow require an 80mm Inner diamter hose/pipe and the turbo intake side requires a 65mm inner diamter hose/pipe. Now to my question, i am looking to get this ( 80mm - 70mm ) https://www.ebay.co.uk/itm/90-Degree...vwF1QDgKuiBt1A Then get a 65mm alloy pipe to put inside the 70mm end and into the turbo intake pipe currently on the turbo (standard one ) , will 70mm compress ok to seal around a 65mm tube ? and is 70mm wide enough to allow good air flow into the turbo over the current black box resonator ? Or do i get an 80mm to 60mm and force the 65mm pipe into it , not sure it will go in tho ? thoughts ? cheers |
this any good to you. https://www.google.com/search?q=suba...ient=firefox-b
|
Ha cheers bud, thats mint ! shame its all in USA, they can get anything/everything at their local motorfactors.
Think i will pop into the pound shop and measure some mugs lol |
no worries, i was going to do the same myself but went front mount instead.
|
They come up on eBay from time to time.... seen a few on there over the last year.
https://cimg3.ibsrv.net/gimg/www.sco...be1dba87cb.jpg |
Yeah cheers bud , that's the 1 I ideally want , made by an Oz firm I think , never seem to find them when for sale only sold lol
I've seen this but not sure it's right , says 92-99 impreza but can't see it working https://cimg6.ibsrv.net/gimg/www.sco...d559022bf2.png |
Originally Posted by MattyB1983
(Post 12009379)
They come up on eBay from time to time.... seen a few on there over the last year.
https://cimg3.ibsrv.net/gimg/www.sco...be1dba87cb.jpg |
You on Facebook, Fred?
Rich will be able to fabricate what you need. https://www.facebook.com/Ellis-fabri...urce=638970516 |
Originally Posted by 1509joe
(Post 12009392)
Have one of these somewhere haven't a clue where its at I'll see can I hoke it out for you its stainless steel if I remember right :thumb:
Hi Ok if it's the same as above not an apexi curved one let me know if you find it |
Originally Posted by mickywrx
(Post 12009394)
You on Facebook, Fred?
Rich will be able to fabricate what you need. https://www.facebook.com/Ellis-fabri...urce=638970516 Cheers for the contact , will get in touch , I've approached a couple of fabricators but they lose interest as soon as you mention the reducer part lol |
I'm looking to modify the one on the v3-v4. Not seen anything aftermarket for them.
|
I have been struggling with this for quite a while. I want to keep my oe airbox but get rid of the resonator box.
At the moment the only way I can get rid of the resonator box is to have a pod filter and delete, which i found on ebay. There are a ton of forum posts on how to make your own, unfortunately there are a ton more referencing the original guides that you have to go through until you find the instructions. There is the coffee cup mod, and there is a guide on how to use silicone pipe that just fits together with jubilee clips and another on what stainless pipe to buy with correct joins and then get a welder to put it together. If I can find them again ill post them up. |
Well after every man and his dog not being able to recreate this I made my own using the coffee cup method.
Will post pics up soon |
All done
Sound so very different lol , being plastic doesn't help I think a metal one will be better but still , intake roar , the fart back through cone filter overpowers the dump valve low down lol . |
|
What did you do about the little take off at the bottom ??
|
I left the boost solenoid hose venting to atmosphere .
I may now have a dabble with blocking off thw dump valve for the turbo flutter sound, being a TD05 it can take it lol |
Originally Posted by The Rig
(Post 12009833)
I left the boost solenoid hose venting to atmosphere .
I may now have a dabble with blocking off thw dump valve for the turbo flutter sound, being a TD05 it can take it lol |
Originally Posted by Rick2017
what is this resonator delete all about. Is there any benefits to it what's involved in it and is it something I can do to my uk2000?
The resonator box was only fitted to the early MY93-96 engines, with top-entry turbos. It sat downstream of the airbox and MAF - between the MAF and turbo intake pipe - and acted as an intake air silencer. So, potentially, being restrictive to airflow: not ideal if you intended to up the power/get mapped. With OEM resonator in place: https://encrypted-tbn0.gstatic.com/i...hnx-Ge6ykXsV9K With a MRT resonator delete pipe (discontinued) in place: http://i48.tinypic.com/1j3kzt.jpg Yours however, being a MY97, is the first MY of the 'under-the-inlet-manifold' front-entry turbo engine layout. So, doesn't have one. |
Originally Posted by joz8968
(Post 12010587)
The resonator box was only fitted to the early MY93-96 engines, with top entry turbos. It sat downstream of the airbox and MAF - between the MAF and turbo intake pipe - and acted as an intake air silencer. So, potentially, being restrictive to airflow: not ideal if you intended to up the power/get mapped.
With OEM resonator in place: https://encrypted-tbn0.gstatic.com/i...hnx-Ge6ykXsV9K With a MRT resonator delete pipe (discontinued) in place: http://i48.tinypic.com/1j3kzt.jpg Yours however, being a MY97, is the first MY of the front entry turbo engine layout. So, doesn't have one. |
:smug:
:lol1: |
Originally Posted by joz8968
(Post 12010590)
:smug:
:lol1: |
I've got a custom setup.
Largest K&N tapered cone I could get in the space below my Hyperflow FMIC intake hard pipe; a cut-down 76mm dia. alloy pipe with a 45-deg bend, between filter and turbo intake hose (I have no MAF, as I have Simtek Mk.2). |
Originally Posted by joz8968
(Post 12010599)
I've got a custom setup.
Largest K&N tapered cone I could get in the space below my Hyperflow FMIC intake hard pipe; a cut-down 76mm dia. alloy pipe with a 45-deg bend, between filter and turbo intake hose (I have no MAF, as I have Simtek Mk.2). |
Well after fitting DIY coffee mod resonator delete ive found my AFR`s are now rich as fook, WOT they are down to 10, they were a steady 11.2 at WOT
Currently even half load goes to 10.8 AFR So, running an ESL ive just lowered the injector scale to flow less fuel but am baffled as to why its more rich with this in place, it doesnt look any less restrictive than the original resonator. all very weird. If i cant map in a suitable AFR i will resort to going back to the resonator box. |
Originally Posted by Rick2017
pics?
Tomorrow evening? |
I left the boost solenoid hose venting to atmosphere . What effect would leaving the boost solenoid vta have? |
Originally Posted by Martianwrx
(Post 12010675)
What effect would leaving the boost solenoid vta have?
|
My pill was removed when it was mapped.
If I do the coffee mug mod as i was planning can i leave the hose vta? Would that be what is causing Rig's afr's to mess up? I dont have the first clue when it comes to mapping. |
1. Should be ok if mapped and yes vta should be ok.
2. Can't see why it would but stranger things have happened. |
All times are GMT +1. The time now is 03:47 AM. |
© 2024 MH Sub I, LLC dba Internet Brands