Subaru Impreza rear bulb holders and loom
So i'm looking for Subaru impreza classic rear bulb holders and loom brand new, i have the passengers side with 3 bulb holders, but the drivers side has a fog light, and can't find a loom and holders for drivers side?
I found these in the USA for passengers side. http://www.ebay.co.uk/itm/SUBARU-OEM...0AAOSwxu5ZMqqo http://opposedforces.com/parts/impre...nic/lamp_rear/ |
If it's a JDM then the fog light bulb replaced one of the reverse bulbs on my car instead of fitting a separate fog lamp.
|
How you mean Rich? As in one side has brake, main lights, reversing and the other had brake, main lights, and rear fog?
|
Originally Posted by jaygsi
(Post 11954112)
How you mean Rich? As in one side has brake, main lights, reversing and the other had brake, main lights, and rear fog?
On mine the main light and brake are on the same dual bulb,then you got indicator and on one side(N/S) is reverse lamp the other (O/S) is fog. |
So if yours standard rear lights? Not JDM?
|
Originally Posted by jaygsi
(Post 11954129)
So if yours standard rear lights? Not JDM?
I'm not sure how a UK car is set up? |
It might be worth buying UK lights and swapping the bits over.
|
I have one uk loom and one JDM. But the uk models have an extra hole for the fog light.
Originally Posted by NOSSY_89
It might be worth buying UK lights and swapping the bits over.
|
Thought your car was a UK car. Are you trying to keep or get rid of the fog light in the cluster.
|
Yes i have a UK Impreza, but just bought a brand new set of STI rear lights. So looking to fit my fog light in, i have 2 looms i think passengers is JDM and drivers side is UK with a fog.
|
I thought so but wasn't sure if you meant what I thought
Just realised yours are brand new. What I was previously suggesting was changing the outer bits and swapping them over. So you would have the UK back and the JDM outer housing. I think the bulb locations are the same. If you don't mind my asking where did you get the lights and how much, pm is necessary. |
Ah didn't think of that, are the backs easy to remove?
Got them off a trader on here. Good price but i believe last ones in stock sorry.
Originally Posted by NOSSY_89
(Post 11954237)
I thought so but wasn't sure if you meant what I thought
Just realised yours are brand new. What I was previously suggesting was changing the outer bits and swapping them over. So you would have the UK back and the JDM outer housing. I think the bulb locations are the same. If you don't mind my asking where did you get the lights and how much, pm is necessary. |
I think I know what ones your mean, it was a few months ago now wasn't it.
Haven't tried it but it should be a case of removing the sealant, there were a few threads on lights that were leaking so similar sort of process really. You might want to check the link below as well. You take the fog light wire and connect it to the bulb where the new fog light will go. https://www.scoobynet.com/scoobynet-...m-classic.html |
Cheers for link some good info there. I still have my old lights if interested.
|
Does anyone have the part number for the drivers side loom?
|
|
I'm after the part code for the complete loom but drivers side as that has extra fog i believe, in the UK lights?
|
Ah the one i posted is for JDM rh side loom,not sure if this software has uk?
I'll have another look,don't suppose you know the applied model code? |
Sorry Rich not a clue.
|
Wasting your time with a JDM loom, on a UK car to get the rear fog light working with STI lights. Red LED bulb in the bulb holder for the fog light on the drivers side, and fit it where the reverse light would go on the drivers side. :thumb:
|
Just to add, if you haven't swapped the rear lights already, and you probably already know this, make sure you seal them well otherwise you'll end up up a flooded boot when it rains.
|
Cheers yeah I know that. Also seen a thread you commented on before about rear fog light conversion. I've decided to buy a rear loom drivers side off a uk model and just swap fog light for reversing light, or just add extra wire and bulb holder to JDM connector.
Plus I need some glue to seal rear lights will see what I have in garage. https://www.scoobynet.com/scoobynet-...m-classic.html |
This stuff is for sealing the lights to the car: http://www.caravan-components.co.uk/...-in-400ml-Tube
Non-setting mastic. DO NOT use glue, silicone, Tiger Seal Sika Flex etc etc. You will never get them out again if you do, and you may need to, (accident etc). Silicone is awful, leaks after about a year, and a pig to remove and reseal. |
Yeah I used silicone last time, was ok at getting off put rubbish at sealing. Ok will get some thanks.
Originally Posted by alcazar
This stuff is for sealing the lights to the car: http://www.caravan-components.co.uk/...-in-400ml-Tube
Non-setting mastic. DO NOT use glue, silicone, Tiger Seal Sika Flex etc etc. You will never get them out again if you do, and you may need to, (accident etc). Silicone is awful, leaks after about a year, and a pig to remove and reseal. |
Why do you need to buy a loom if yours is a UK car, or do you not have it anymore?
The bulb loom is held onto the back of the cluster by 1 screw from memory. |
Originally Posted by ossett2k2
(Post 11954527)
The JDM version is in Japanese ....... http://clarkdh.net23.net/NTL/94wrx.PNG |
UK loom went with my old lights.
Originally Posted by mickywrx
(Post 11955263)
Why do you need to buy a loom if yours is a UK car, or do you not have it anymore?
The bulb loom is held onto the back of the cluster by 1 screw from memory. |
The loom posted by ossett2k2 above is for European RH (UK) version
Part number 84931FA130 (includes foglight socket). UK LH loom is the same as the later JDM version 84931FA280 (Early and Later versions shown below) http://clarkdh.net23.net/NTL/JDM%20light%20looms.PNG |
Originally Posted by Don Clark
(Post 11955269)
Not sure what version of Subaru Fast this is but it sure isn't for JDM models.
The JDM version is in Japanese ....... http://clarkdh.net23.net/NTL/94wrx.PNG Came on a disc with a few workshop manuals,had it for years but wasn't sure how to use it properly until you told me how :) There is a drop down tab where it say 'grade' and it had JDM models as an option. |
Thanks Don and Rich now armed with part numbers i'm on the hunt :thumb:
Originally Posted by Don Clark
(Post 11955274)
The loom posted by ossett2k2 above is for European RH (UK) version
Part number 84931FA130 (includes foglight socket). UK LH loom is the same as the later JDM version 84931FA280 (Early and Later versions shown below) http://clarkdh.net23.net/NTL/JDM%20light%20looms.PNG |
All times are GMT +1. The time now is 01:13 AM. |
© 2024 MH Sub I, LLC dba Internet Brands