Andy Carr pre - map advice
As per title, will be booking my03 sti ppp in for opensource remap.
Ive just completed full service, new timing belt / pulleys , waterpump, crank sensor, engine coolant sensor, front lambda, maf, coolant etc So, is their anything else i need to get? new/uprated mapsensor, or is oem ok? 3 port solenoid, should i just get Andy to price one in or buy before hand? Is it also worth having the 2 map switch? Also to add ive fitted new green panel, pfr7b's, miltek centre pipe and deatsch werks 300 fuel pump.. cheers Dan |
Oil?
|
it would be worth fitting a downpipe as well to get the most out of the map, the switches you'd be as handy getting fitted and mapped in now so you can chose to use them or not.
|
Originally Posted by veerinder9
(Post 11851336)
Oil?
|
Originally Posted by bludgod
(Post 11851398)
it would be worth fitting a downpipe as well to get the most out of the map, the switches you'd be as handy getting fitted and mapped in now so you can chose to use them or not.
Right, I'll get the switches put in, not keen on the rear demist switch/ wot activation. What's your thoughts on the map sensor, OK with oem? |
Map sensor reads to about 1.55 bar so unless you plan on running more than that leave it, 3 port boost solenoid would be nice as it will give you better boost control and I would fit the switches before hand as it saves time
|
Originally Posted by Whit80
(Post 11851425)
Was just going to leave the prodrive sport cat in to save switching around.
Right, I'll get the switches put in, not keen on the rear demist switch/ wot activation. What's your thoughts on the map sensor, OK with oem? |
that's the ECUtek 100% throttle map switch, with carberry it's just on /off so if demister is on your on the second map. Mister off and your on first map (or used for on/off of antilag which will surely end your PPP cat very quickly).
With the toggle switches fitted it will be the same you'll have clear on/off with the switch. |
Originally Posted by bludgod
(Post 11851433)
that's the ECUtek 100% throttle map switch, with carberry it's just on /off so if demister is on your on the second map. Mister off and your on first map (or used for on/off of antilag which will surely end your PPP cat very quickly).
With the toggle switches fitted it will be the same you'll have clear on/off with the switch. |
yes you can use cruise control if you have it - otherwise you just count the flashes when you switch maps - 1 flash on the engine light for primary map, multiple flashes (i think it's 8 flashes?) for the second/race map.
|
Mine has only one map with high and low boost,
Earlier 2003 car no cruise, Yes, i am on ECUtek. My EML doesnt flash when i change from low to high boost. But no way of knowing which of the two i am set at ? |
Originally Posted by bludgod
(Post 11851433)
that's the ECUtek 100% throttle map switch, with carberry it's just on /off so if demister is on your on the second map. Mister off and your on first map (or used for on/off of antilag which will surely end your PPP cat very quickly).
With the toggle switches fitted it will be the same you'll have clear on/off with the switch. I'll have to look at getting a de-cat, although I won't be getting launch control, anti lag etc |
Originally Posted by SmurfyBhoy
(Post 11851439)
Mine has only one map with high and low boost,
Earlier 2003 car no cruise, Yes, i am on ECUtek. My EML doesnt flash when i change from low to high boost. But no way of knowing which of the two i am set at ? Although not ideal, should indicate what map your on |
Originally Posted by Whit80
(Post 11851506)
Can you not feel the difference between the two, do you have a boost gauge fitted?
Although not ideal, should indicate what map your on My point is without bringing it into boost, No sign of which of the two it's in till you press the pedal and see. |
[QUOTE=SmurfyBhoy;11851528]Yes, obviously :lol1:
My point is without bringing it into boost, No sign of which of the two it's in till you press the pedal and see.[/QUOTE ] :-) Not stating the obvious! Just wondered if their was not much difference between the two maps to the point you couldn't tell.. |
[QUOTE=Whit80;11851592]
Originally Posted by SmurfyBhoy
(Post 11851528)
Yes, obviously :lol1:
My point is without bringing it into boost, No sign of which of the two it's in till you press the pedal and see.[/QUOTE ] :-) Not stating the obvious! Just wondered if their was not much difference between the two maps to the point you couldn't tell.. 1 bar (actuator) and 1.7 bar |
So until I actually bring the boost on I don't know which i am in :)
|
I can switch maps with I/C button, Auto I/C on high boost 1.5 bar, Auto I/C off low boost 1.0 bar
|
Originally Posted by bro82
(Post 11851597)
I can switch maps with I/C button, Auto I/C on high boost 1.5 bar, Auto I/C off low boost 1.0 bar
|
Yeap, another advantage of jdm
|
Originally Posted by Whit80
(Post 11851294)
As per title, will be booking my03 sti ppp in for opensource remap.
Ive just completed full service, new timing belt / pulleys , waterpump, crank sensor, engine coolant sensor, front lambda, maf, coolant etc So, is their anything else i need to get? new/uprated mapsensor, or is oem ok? 3 port solenoid, should i just get Andy to price one in or buy before hand? Is it also worth having the 2 map switch? Also to add ive fitted new green panel, pfr7b's, miltek centre pipe and deatsch werks 300 fuel pump.. cheers Dan |
Originally Posted by merlin24
(Post 11851871)
Neutral Position Switch ?
Really need to get romraider up and running..... would a neutral pos switch issue have an affect on remap and in what way? Dan |
if the NPS isn't working then the AVCS won't engage so the turbo will be slower to spool and you'll miss out on some nice midrange torque. Don't just check at idle check it on a drive as well to make sure it's blipping 0/1 when changing gear too.
|
Originally Posted by bludgod
(Post 11852088)
if the NPS isn't working then the AVCS won't engage so the turbo will be slower to spool and you'll miss out on some nice midrange torque. Don't just check at idle check it on a drive as well to make sure it's blipping 0/1 when changing gear too.
As you say,I've only checked on idle. I'll have a check when I finish work.. |
Do you have a contact number for Andy Carr? Been mapped by him before but lost the number. tried email but no luck,
Cheers |
Originally Posted by Ash Webster
(Post 11852194)
Do you have a contact number for Andy Carr? Been mapped by him before but lost the number. tried email but no luck,
Cheers |
Originally Posted by Whit80
(Post 11852197)
Sorry mate I don't...was going to email myself as soon as I know car is 100%
|
Talk to Matty at MB Developments :thumb:
He can sort it and get it arranged for you. Andy mapped my both old Imprezas and just mapped a friend of mine through Matty |
Originally Posted by birchy2010
(Post 11852250)
Talk to Matty at MB Developments :thumb:
He can sort it and get it arranged for you. Andy mapped my both old Imprezas and just mapped a friend of mine through Matty |
your better off phoning TEG sport or Poleposition as he's there weekly as said Andrew is very busy
That way your guaranteed to get booked in |
All times are GMT +1. The time now is 05:44 AM. |
© 2024 MH Sub I, LLC dba Internet Brands