ScoobyNet.com - Subaru Enthusiast Forum

ScoobyNet.com - Subaru Enthusiast Forum (https://www.scoobynet.com/)
-   East Anglia (https://www.scoobynet.com/east-anglia-435/)
-   -   recommend geo place pls (https://www.scoobynet.com/east-anglia-435/1020947-recommend-geo-place-pls.html)

savage bulldogs 03 March 2015 07:23 PM

recommend geo place pls
 
Looking for a tried and tested place to get a geo set up done near the essex/Suffolk boarder .
can anyone recommend somewhere and if so what set up did you get done (standard .prodrive fast road ect ...)
Cheers clive

BBB3 03 March 2015 09:27 PM

Hi Clive,

I know this is too far but if you are ever in Norwich, Dave @ Autotest up the Air Port Ind Est.

He's done my Classic with KTS coilovers, My Evo 8MR with Bilsteins and my Spec c :)

savage bulldogs 03 March 2015 10:23 PM

Thanks for that and no it's not to far to get something done properly .

I get my mapping done in Norwich and tbh it's a shame I haven't got my rear camber bolts already

as I'm @attowes this friday getting the apexi fc tweeked

BBB3 04 March 2015 07:07 AM


Originally Posted by savage bulldogs (Post 11638494)
Thanks for that and no it's not to far to get something done properly .

I get my mapping done in Norwich and tbh it's a shame I haven't got my rear camber bolts already

as I'm @attowes this friday getting the apexi fc tweeked


Well Dave at Autotest is a good friend of Clive's, you may well see my Spec at Clive's just waiting for a call so I can drop it off for it's service

Clive mapped my spec c ;)

ditchmyster 04 March 2015 07:53 AM


Originally Posted by savage bulldogs (Post 11638494)
Thanks for that and no it's not to far to get something done properly .

I get my mapping done in Norwich and tbh it's a shame I haven't got my rear camber bolts already

as I'm @attowes this friday getting the apexi fc tweeked

Give Alyn at AS Performance a call he'll probably get them to you in the post by tomorrow. ;)

Other point is what's your car and set up, what are you after achieving and using the car for, as those are the factors that will determine what settings you should go for.

savage bulldogs 04 March 2015 12:00 PM

V1 sti
2ltr forged currently running 330@1.1 bar due to a misfire during attowes last remap (hopefully more after the tweek with the newage coilpacks in situ)
elbiach pro springs
whiteline adjustable arb, links and roll centre correction kit .
It's a daily driver but I reshelled it a couple of months ago and have only had the tracking set so far just want to get the most of my mods , make sure it's aligned correctly and a bit more over steer would be nice

ditchmyster 04 March 2015 01:54 PM

Have a read of this thread, post 54 is what you'll be interested in though.

https://www.scoobynet.com/1016983-bi...k-roads-2.html

savage bulldogs 06 March 2015 04:19 PM

Cheers for that ditch , I had heard that the prodrive set up tends to scrub your tyres a bit but tbh it's all witchcraft to me anyways so I'll let dave work his magic next time I'm at attowes

BBB I went to attowes today ,no spec c in site though :-(

Not much luck on the dyno for me either :-(

seems like my antique apexi super intake is throttling my engine as it was making 1.4 bar just under 4k but couldn't hold it to the limiter.

end result was same 330 hp with a increase of 60 lbs of torque at 3.5k (not all bad) but not the 360 hp pub figure I was hoping for

ordered a few bits to fit a mahusive k&n; hopefully I'll have better luck next time

ditchmyster 06 March 2015 04:27 PM

I run a little less Toe than the Prodrive settings as that's what scrubs your tyres, but all my settings are for my Blob Wagon, When I had my Type R done I was like you and didn't really know anything about it (not that I do now) but it only costs me 20 quid at my local tyre place so I keep trying different settings, I'm on winter tyres at the moment so not driving so fast using -1 less camber than I was and running closer to prodrive set up, but that will change for the summer.:D

BBB3 06 March 2015 10:15 PM


Originally Posted by savage bulldogs (Post 11640359)
Cheers for that ditch , I had heard that the prodrive set up tends to scrub your tyres a bit but tbh it's all witchcraft to me anyways so I'll let dave work his magic next time I'm at attowes

BBB I went to attowes today ,no spec c in site though :-(

Not much luck on the dyno for me either :-(

seems like my antique apexi super intake is throttling my engine as it was making 1.4 bar just under 4k but couldn't hold it to the limiter.

end result was same 330 hp with a increase of 60 lbs of torque at 3.5k (not all bad) but not the 360 hp pub figure I was hoping for

ordered a few bits to fit a mahusive k&n; hopefully I'll have better luck next time

The Spec C was booked in for Thursday but I'd had to change so it's in next Tuesday now, hopefully next time I'll be about and pop up :thumb:


All times are GMT +1. The time now is 12:32 PM.


© 2024 MH Sub I, LLC dba Internet Brands