Cookstars "mystery machine" drag/track project
 

I thought I'd start a little thread with what's going on with my 99 UK 2000

It started off with me as a £500 runabout through the winter. I bought it as a non runner (unplugged MAF sensor and drove home in it:D)

When I picked it up it had a printout from SRR (mapped by JGM) for 318 BHP.

Here's a few pics of how she stands now.

http://i164.photobucket.com/albums/u...ps8b29dbed.jpg

http://i164.photobucket.com/albums/u...ps3ad6c336.jpg

http://i164.photobucket.com/albums/u...ps0e7ffe04.jpg

http://i164.photobucket.com/albums/u...ps3833ffe0.jpg

http://i164.photobucket.com/albums/u...ps198352fd.jpg

http://i164.photobucket.com/albums/u...pscb48a06b.jpg

http://i164.photobucket.com/albums/u...ps4a49140a.jpg

http://i164.photobucket.com/albums/u...psf553a342.jpg

Spec list is as follows

Engine (current)

Unknown.:lol1:

Turbo

VF20

Gearbox

STI7 6 Speed box, dif, hubs etc etc.

Brakes

Front Newage Brembo calliper with PF pads and uprated discs
Rear Brempo with standard pads and discs

Exhaust

Full 3 inch decat system (turbo back)

Fuelling

SWRD 290 fuel pump

Suspension

Tein superstreet coilovers

Wheels and tyres

18 inch inovit with 225/40/18 T1rs


The car is going away on Sunday to have the following fitted. (some pics below)


SC46 turbo
RCM wrapped headers and up pipe
Engine tuner 2.1 stroker
RCM head gaskets
RCM header fitting kit
Kevlar timing belt
Newage Spec C heads
Lateral performance 900 cc flowed injectors
Hyper exedy twin plate clutch

Alcatek ECU with A/L & L/C enabled.
Perrin 4 bar MAP sensor
JT innovations AVCS loom
JT innovations Newage coilpack conversion
3 port boost solenoid

Mapping to be carried out by JGM, several maps including meth.
Car is to be run maffless.

http://i164.photobucket.com/albums/u...psc0757713.jpg

http://i164.photobucket.com/albums/u...ps6deb2ec8.jpg

http://i164.photobucket.com/albums/u...ps9896d795.jpg

http://i164.photobucket.com/albums/u...ps462cc74a.jpg

http://i164.photobucket.com/albums/u...psed314b95.jpg

With a 20%meth map I'm hoping to achieve around the 500 BHP mark. :norty:




Current running spec

Currently running 430.6 BHP (Mapped by JGM)

Chassis
Stripped interior
Boot floor cut away and replaced flat
Beatrush rear dif brace
Front strut brace

Suspension & Brakes

Tein Superstreet coilovers.
Front newage Brembo - standard discs with PF pads
Rear newage Brembo - stadard disc and pads

Wheels & Tyres

Inovit Tarmac with 225/40/18 Toyo t1R

Running Gear

STI7 6 Speed gearbox + matching rear dif
R180 rear hubs + matching shafts

Engine
(enginetuner built) 2.1 CDB Stroker
Newage Spec C (AVCS) large port cylinder heads.
Mahle Pistons
Cosworth extreme 11mm head stud conversion
Cosworth timing belt guide
RCM oil pump
RCM head gaskets
SC46 turbocharger
Kevlar timing belt
NGK "7's"
Samco silicone inlet
Samco water piper kit
Hybrid FMIC
Dump valve delete
Induction kit
Header tank spacer kit

Exhaust

RCM GT spec headers and venturi up pipe (fuly wrapped with DEI)
RCM fitting kit for headers and up pipe
True 3 inch decat downpipe
3 inch (unknown brand) centre section and backbox


Electronics

Alcatek ECU - motorsport enabled, so A/L and launch control enabled also modified for VVT
Newage coilpack conversion
JT innovations hybrid loom for newage coilpacks and AVCS into classic.
Perrin 4 BAR map sensor
3 port bost solenoid.


Fuelling
SWRD 290 Lph in tank pump
440 injectors (flowed to ~900cc by Lateral Performance)


Bodywork mods

Bonnet pins fitted
Rear spoiler removed

Interior

Snap off steering boss
Sparco steering wheel

About time you started one up:DSubcribed.SJ.

Nice one and good spec your going for, look forward to seeing how it comes along :)

you paid £500 for that with a 6 speed and brembos???

If it did cost that, it was the bargain of the century! :lol1:

Sorry, should have made that clear, since I bought it, I have added the coilovers, brakes and gearbox. :)

Also the wheels


Only changed spark plugs and Maf on the engine side though, with the downpipe decat it made 341 at Surrey Rollng Road, about an hour before spitting its head gaskets out. :lol1:

Suscribed Mate !!

Looking forward to seeing this blast up the Pod !:luxhello:

Me to mate, mapping is booked for the 22nd & 24th so fingers crossed you'll see it on the 27th. :norty:

I'll be dropping you a PM shortly mate, I need a bung making up for the dump valve delete.

New addition to the ever growing pile of heavy expensive stuff in the dining room. :D

Hyper Exedy twin plate clutch.

http://i164.photobucket.com/albums/u...ps612018e8.jpg

Got it used, only had a couple of weeks very light use.

Ok mate ,

Just send me the details and can machine you one whilst still on nights 😉
I'm booked in for 1st October for alcatek / meths map

I'll go and have a measure up now. :thumb:

It's about time you started this thread..... It's even got me back on Snet after a long time away....
Now get cracking with it cos I wanna start making it look special 👍

All in hand my son. You done that sample yet :norty:

Not the urine kind though.. :Suspiciou

It hasn't arrived yet, only shipped today. Might come in tomorrow but got plenty of time for that 😉

Been on to JT innovations today, and have ordered a hybrid AVCS conversion/new age coilpack conversion loom.

Bit pricey, but hey ho. :)

RCM headgaskets, RCM headers and up pipe fitting kit, and a timing belt ordered today :eek:

Wallets taken a right pounding. :D

I do like reading about people's projects,always plenty of different ideas.
Good luck with this one and deepest sympathies to your wallet.

Thanks mate. :thumb:

Picked this lot up tonight, should keep me going for a while...


http://i164.photobucket.com/albums/u...pscbe05bd0.jpg

Some choice parts there. Will make for a great motor.

My mate popped over and fitted some bonnet pins today, cheap but functional. The bonnet latch doesn't catch if you pop the bonnet, so I lost any trust I had with it.

As soon as I source a ally bonnet I'll stump up for some nicer aero catches.

http://i164.photobucket.com/albums/u...ps5e3ece29.jpg

Off she goes today with a boot full of goodies to be put together..

My finger nails are getting a battering today.

http://i164.photobucket.com/albums/u...ps8cd1c3de.jpg

http://i164.photobucket.com/albums/u...ps1066b75c.jpg

http://i164.photobucket.com/albums/u...ps6e1b806d.jpg

http://i164.photobucket.com/albums/u...psc15d56b0.jpg

AA recovery? did you tell them it broke down? hah

It did. Head gasket went. ;)

Nice one Cookie. You're a man on a mission. :thumb:

Haha, thats one way of doing it! Some nice parts going on this, I need a kick up the ass tog et mine finished :(

Dump valve delete bung, head gaskets, JTi looms, and header fixing kit have arrived today.

Only part outstanding is the ECU to be returned from Alcatek. They have assured me that it will be with the garage by Friday (crossing fingers/toes and everything else)

JGM is booked to put a base map on the car on Monday, to get the car drivable and to be able to test, ready for full mapping on Wednesday at Surrey. :luxhello:

Just noticed this, subscribed! :thumb:

Regards,

Subaru Collector 555.

Right so work is underway, watch this space

[IMG]http://i1347.photobucket.com/albums/...ps2527fdd8.jpg[/IMG]

Engine out

[IMG]http://i1347.photobucket.com/albums/...ps84b9aa7a.jpg[/IMG]

[IMG]http://i1347.photobucket.com/albums/...psa51c814a.jpg[/IMG]