thanks mate, not had chnace to touch it tonight, took bits to work and cleaner, and plan was to re seat vales and fit heads and cams and work out shims sizes i need.

but my bro in law made light work of that, nabbed me on way home, and now i got home. problems with hit mitsubishi fto.

think im just too nice 2 ppl.

hand a good 2 hrs on it tonight, manages to re seat valves and switch valve train over from old head to new. fitted head back to block and toqued down and checked valve clearances and noted all then measurments.

tomorro cams and shims are back off for measuring to work out what size shims i need for corect clearance, easy job but time consuming, and may av 2 get shims ordered, but i have 32 shims here to measure so hopefully 16 will all b in tolerance and i can get rocker covers on and start the bolting things back on.

il post a few pics 2morro and small formula for working out clearances etc.

looking to fit engine by end of january providing i dont deciede to chnage anything along the way.

Subscribed to this awesome thread - keep up the good work!

made a nice bit of progress on heads tonight, managed to work out what size shims i need. i measured all 16 i had a put in table below showing working out and showing how to do the calculations.

http://i186.photobucket.com/albums/x...ooxa/shim2.jpg

also pics of the equiptment used below. feeler gauge, digital verniers and micrometer

http://i186.photobucket.com/albums/x...a/DSC00265.jpg

below im checking valve clearance with feeler gauge

http://i186.photobucket.com/albums/x...a/DSC00266.jpg

http://i186.photobucket.com/albums/x...a/DSC00267.jpg
Shim off bucket ready for measuring

http://i186.photobucket.com/albums/x...a/DSC00268.jpg
Micrometer

http://i186.photobucket.com/albums/x...a/DSC00269.jpg
digital verniers


due to problem i had with my old head i had 2 buy a pair of heads which has worked out great as iv got an extra 16 shims.

http://i186.photobucket.com/albums/x...a/DSC00270.jpg

iv also measured them and seems lady luck was on my side as i have all the shim sizes i need to assemble heads fully and final time 2morro evening.

got a new water pump gasket on order with subaru and cam covers in work ready for some paint, going blue.

The only difficulty i may have now is timing. but im very confident

then it seems it all bolt on stuff and making any extra parts such parallel fuel mod and decieding to fit lightweight flywheel now or after run in. decisions.

if i wait then it delays me getting it back on rd. if i dont, extra wrk for myself.

ok, tonight ive fitted new shims in place and re checked for clearances, 3 cams worked out brillain all in tolerances desired, but one cam was a bit rogue and took 3 attempts. 1 shim didnt want to give me the correct clearance. As i had all shim sizes 0.99 0.98 0.97 etc, i decresed shim by 0.01 untill i had desired clearance. i started with a 0.10 shim and had correct clearance at 0.98. so im very happy with the head building.

now im waiting on myself to get rocker covers 2nd coat done and finish paint work on block.

tomorrow im tackling parallel fuel mod and preping cam covers.

then a big sort out and make sure i have the bits it need and get them organised ready to be fitted.

Keep it up, you're doing great now. I feared the timing stage myself, but in the end it was a piece of piss with the engine sat there in front of me on the stand. Once I'd put the ex and in cams the right way round that is LOL

yeh, i read that lol, so easy to do tho mate. especially when progress is being made. the way i see it now, end of january il be fitting engine. but all depends if i deciede to fit harveys heads n up pipe, or run and and then fit at a later date, just i kno the up pipe is horrible to change once fitted.

i guess il see how progress goes, as im waiting on myself to paint bits on work and do the little jobs now.

painted block about 5 mins ago and end coat on rockers, havent painted underside of engine yet as waiting before i can tuen engine over, decieded while im there to paint sump blue :)

took a while, about hours and half to do, its not perfect and some areas will ne touching up with a smaller brush, but it will look good in the engine bay, even tho most is out of sight, only applied one coat as dont want to affect the heat soack too much, but to help this the race rad will be fitted to keep things cooler.

also put come colour on crank pulley, make it llok nice against blue cam covers
now im going to do fuel mod so i guess il post in a bit aswell.

http://i186.photobucket.com/albums/x...a/DSC00279.jpg

http://i186.photobucket.com/albums/x...a/DSC00280.jpg

http://i186.photobucket.com/albums/x...a/DSC00281.jpg

http://i186.photobucket.com/albums/x...a/DSC00282.jpg

http://i186.photobucket.com/albums/x...a/DSC00283.jpg

Your getting there mate :)

ok, im now done for today ordered chinese, so a quick write up.

iv painted the underside of block and sump blue.
made my parallel fuel mod but unfortunatly i need a 8mm brass elbow to run my aftermarket fpr, im getting this of carl davey webside, so should b here in a few days. iv taken pics of every stage i done as when looking in search on sn, i cudnt find stage by stage only complete diagrams. its not the best but it should help. i havent fitted any clips yet.

pipe cutter used
http://i186.photobucket.com/albums/x...a/DSC00289.jpg

Brass t-pieces
http://i186.photobucket.com/albums/x...a/DSC00290.jpg

assembled off manifold ready for cutting
http://i186.photobucket.com/albums/x...a/DSC00291.jpg

Cut 1 also shown on manifold
http://i186.photobucket.com/albums/x...a/DSC00292.jpg
http://i186.photobucket.com/albums/x...a/DSC00293.jpg

Cuts 2 and 3, also shown on manifold
http://i186.photobucket.com/albums/x...a/DSC00294.jpg
http://i186.photobucket.com/albums/x...a/DSC00295.jpg
http://i186.photobucket.com/albums/x...a/DSC00296.jpg

Injectors in place, 1st fuel line run in
http://i186.photobucket.com/albums/x...a/DSC00297.jpg

1st fuel line with t piece installed
http://i186.photobucket.com/albums/x...a/DSC00298.jpg

2nd fuel line run in
http://i186.photobucket.com/albums/x...a/DSC00299.jpg

2nd fuel line t-piece installed
http://i186.photobucket.com/albums/x...a/DSC00300.jpg

Fuel inlet and output line in, fpr for display purposes showing where pipes lead
http://i186.photobucket.com/albums/x...a/DSC00301.jpg

Fuel mod shown with no manifold, showing setup from injectors and inlet,output lines
http://i186.photobucket.com/albums/x...a/DSC00302.jpg


need to fit 8mm brass elbow here to run fpr
http://i186.photobucket.com/albums/x...a/DSC00285.jpg

Underside of engine painted and blue sump
http://i186.photobucket.com/albums/x...a/DSC00288.jpg
http://i186.photobucket.com/albums/x...a/DSC00287.jpg

going well fella top work

Sorry but the fuel lines are rough at best.

The price of stainless 8mm tube and fittings it would be rude not to do a "proper job"

it is what it is, and it does the job, they will be braided over to look bit better but as they arnt exactly in your face in engine bay, and i cant see them when im driving, so i went for the budget model.

thanks mate, iv been keeping an eye on your thread. and imo ur car is one of the nicest iv seen.

what internal size fuel hose do you need for this?

Well mine are the same - rails cut with a pipe cutter and deburred, standard 8mm fuel hose and brass tee pieces, doubled jubilee clips at each tail to be on the safe side, job done - no problems, no leaks. And it all fits easily under the manifold even if it doesn't look fancy or over engineered.

ok, done a little bit more this morning, managed to fit rocker covers, water pump and some timing covers are on. also painted inlet manifold in work. may paint a few brackets 2 add some more colour.

next step is to carry engine into garage and build and fit manifold, turbo, headers, exhaust, timing, flywheel, clutch, alternator, powersteering, starter motor and connect electrics and hoses, breathers etc

decieded to wait for clutch do wear before i fit lightened flywheel and probably same time fit ppg box, race clutch, give me time 2 save.

heres a few updated pics

http://i186.photobucket.com/albums/x...a/DSC00308.jpg

http://i186.photobucket.com/albums/x...a/DSC00309.jpg

http://i186.photobucket.com/albums/x...a/DSC00311.jpg

http://i186.photobucket.com/albums/x...a/DSC00315.jpg

http://i186.photobucket.com/albums/x...a/DSC00316.jpg

http://i186.photobucket.com/albums/x...a/DSC00317.jpg

looking very good, just one thing, i dont think the your inlet manifold in the 5th picture up will fit on your engine, its bigger than the man spraying it, ha ha ha ha ha.

i like tha, lol, didnt notice :)

well new water pump gasket arrived, so has inlet and fpr bypass adapter,
so tomorro the engine is being transported to garage and built up ready for aimed start date 1st feb. mayb... if i do some serious work :p

moved engine from bk bedroom to garage tonight, help of a mate. gitted new water pump gasket, headers, uppipe, turbo and flywheel.

inlet manifold is 90% assembled and tomorro im taking water pipe to work that runs over block. timing belt will be here saturday :) and engine fully build up by staurday evening. thinking of trying to fit engine sunday. good weekend finishing off.

few pics of 2day

http://i186.photobucket.com/albums/x...a/DSC00320.jpg

http://i186.photobucket.com/albums/x...a/DSC00321.jpg

http://i186.photobucket.com/albums/x...a/DSC00322.jpg

looking good fella give us a shout if you do get it in the car :thumb:

ordered timing belt kit ftom AS Performace today. £200 delivered. should arrive monday - tuesday. all is on track for a week sunday start. lots to do over weekend so il post 2moz evening.

looking good there matey :thumb:

me n a mate spend some time in the gareg and fitted some more bits. inlet manifold, pipe work, engine mounts, etc, a few pics of my progress.

http://i186.photobucket.com/albums/x...a/DSC00324.jpg

http://i186.photobucket.com/albums/x...a/DSC00325.jpg

http://i186.photobucket.com/albums/x...a/DSC00326.jpg

http://i186.photobucket.com/albums/x...a/DSC00327.jpg

Good stuff, keep going!

back down the garage this morning to fit a few more bits. fitted the exhaust now ready and parallel fuel mod is in place. power steering, alternator and air con units r in place, although the alternator isnt bolted up, as i need 2 prime the pump. need to find out exactl;y where the knock sensor goes, had a look, bit unsire, so think il search that. everything seems to be going to plan, manifold can get a bit messy rtunnign all the pipes bk in. i shud av fitted fuel mod and pipe from block to header tank before i bolted manifold down.
waiting on timing kit tommorrow and also need 2 to torque cam pulleys, crank pully.

for this im gonna use old belt and maul grips to keep tension so cam doesnt rotate when torquing.

all thats left now is to give engine bay a quick clean with gunk, not gonna go 2 mad, after all its is a engine bay.

any1 give me advise on how to fit clutch fork. do i bolt engine to box and then fit it, or can u fit it to clutch and then line engine up 2 box and angle it out of the hole?

heres some pics, and for those who notcie, the subaru logo on the boot is upside down, lol :)

http://i186.photobucket.com/albums/x...a/DSC00331.jpg

http://i186.photobucket.com/albums/x...a/DSC00332.jpg

http://i186.photobucket.com/albums/x...a/DSC00338.jpg

http://i186.photobucket.com/albums/x...a/DSC00336.jpg

http://i186.photobucket.com/albums/x...a/DSC00333.jpg

http://i186.photobucket.com/albums/x...a/DSC00334.jpg

http://i186.photobucket.com/albums/x...a/DSC00335.jpg

Before dropping the engine in, fit the release bearing to the driveshaft and the fork, insert the pivoting dowel through the side of gearbox and then the blanking bolt. I find it much easier doing that than having the bearing already on the clutch.

quick update, nothing done, not happy, waiting for a timing kit that should have turned up yesterday, so lost 2 days building, doubt il make my time scale now, very gutted, and got a busy week ahead so not working on my car. i love sh!t companies

well it wasnt the companies fault on timing belt, my neighbour had it since 11.30 monday morning. after giving companty and couriers grief, they said its been signed for by no.4, great, how then kept in it there house untill i knocked tonight at 7pm. thanks, lol

well iv timed the engine and fitted covers tonight, was all correct 1sty time around, turned engine over, turned smoothly, so very happy. coveres all fitted, ready for fitting friday night as im busy tomorro, gutted.

doubt i will be on for a sunday start now, but il do my best fri night, sat n sun.

just gotta buy 4 oil filters and i think 10w 40 oil to run in. changes after 1st 15min run, then 100 miles, then 500 and eventually 1000 with better oil.

http://i186.photobucket.com/albums/x...a/DSC00340.jpg

as it stood when i just left garage

You're catching me up! Good work!