Originally Posted by trails
(Post 11771318)
Sensible mods so far, but speaking from experience the 18g is a great blower on a 2.0 so would be epic on a 2.5 :)
I couldnt find anyone that could tell me which turbo would get me from 0 - 60 quickest at 1.2 bar, so i guess i'll have to find out myself :-) Then share with everyone on here once i've done it. That could be a little while though, i'm very close to the point of being fed up of spending! lol Once its mapped (next week fingers crossed) i'm going to have to give my bank balance a little break! |
Will be interesting to see the results, worst case scenario run 1.4bar andthen drop a 2.0 bottom end in if it goes pop :D
|
Originally Posted by trails
(Post 11771334)
Will be interesting to see the results, worst case scenario run 1.4bar andthen drop a 2.0 bottom end in if it goes pop :D
LOL i'll have to wait for the bank balance to bounce back for that :-) I would like to forge the engine though, so that i can get the most out of it, instead of worrying about it. But, thats a long way away right now :-) |
Whiteline 22mm roll bar at the front, and 24mm roll bar at the back going on today :-) With some whiteline roll bar mounts at the back. Cant believe how much the rear roll bar weighs!!
Super Pro rear drop links also going on! :-) https://cimg5.ibsrv.net/gimg/www.sco...54d109f545.jpg https://cimg6.ibsrv.net/gimg/www.sco...0f808d7b3c.jpg |
Right, now new years is out the way, time to continue!
Anti lift kit on, lower H brace on, Alloy arms with new drop links on! Took me ages to find hawk STI alloy arms, i needed ones from the hawk because there is something that connects to the front headlight leveling mechanisms! Had a little problem with the lower H brace too, the holes needed widening to fit the bolts, and some of the edge needed to be cut to make it fit! https://cimg6.ibsrv.net/gimg/www.sco...6d35aedff4.jpg https://cimg9.ibsrv.net/gimg/www.sco...13d2084a12.jpg https://cimg8.ibsrv.net/gimg/www.sco...e4bc0ba386.jpg https://cimg0.ibsrv.net/gimg/www.sco...cf10285653.jpg https://cimg7.ibsrv.net/gimg/www.sco...4050a2d493.jpg Only a Geo set left to go, then the suspension side of things are done! For now ;-) |
Geo set up booked for Sunday :-)
|
That's looking ace. Well done. Should really stiffen things up.
|
How are you getting on with the ARB's? I'm considering the rear but probably leaving the front for now.
|
Just seen the thread, it certainty will be a little sleeper!
Has it been mapped yet? Matt. |
Wow, this project has fallen on the back burner and literally hasnt had anything done since the Geo set up in Jan!!!
In that time i have decided to fit the Harvey Smith 18g. Loads and Loads of people have told me it will just be a waste putting the TD04 Hybrid on. So i've come to my senses and listened to everyone :-) |
Also have a set of kinugawa equal length headers to go up, with a harvery smith trick up pipe.
I've had equal length before, and did miss the Scooby rumble, but did also like the refined, quiet sound at low speeds (i'm getting old!). https://cimg7.ibsrv.net/gimg/www.sco...bdf9788340.jpg https://cimg1.ibsrv.net/gimg/www.sco...0002cc8d7a.jpg |
Glad you came to your senses with the turbo choice! :)
|
Originally Posted by BrownPantsRacing
(Post 11825271)
Glad you came to your senses with the turbo choice! :)
|
Originally Posted by Reshard1977
(Post 11825272)
i should of just listened to you (and everyone else) from the start!
|
Little update! :-)
I decided to get my Harvey Smith TD05 18G ceramic coated and have a billet wheel fitted! This project is taking much longer than i want, life keeps getting in the way! But, i'm told the best things come to those who wait! :-) https://cimg6.ibsrv.net/gimg/www.sco...9b06f4e6f4.jpg https://cimg9.ibsrv.net/gimg/www.sco...8629c8d620.jpg https://cimg1.ibsrv.net/gimg/www.sco...083fc066ab.jpg |
Lovely turbo choice. Seen these make really good power on a 2.5 engine. I was torn with going for a Harvey 18G or a VF48 on mine, but the VF48 landed at a very reasonable price so on it went! :)
|
Originally Posted by BrownPantsRacing
(Post 11837473)
Lovely turbo choice. Seen these make really good power on a 2.5 engine. I was torn with going for a Harvey 18G or a VF48 on mine, but the VF48 landed at a very reasonable price so on it went! :)
Out of curiosity, what power have you seen a HS 18G make on a WRX 2.5? I know 2 identical cars could make quite different power, but just curious. I bought the HS turbo as a bit of an impulse buy, becuase they always seem to have good feedback. But now the impulse moment is over, do you know what makes the HS 18G different from a "regular" 18G? |
When Duncan mapped my hawkeye years back he'd just mapped a GB270 wagon with a Harvey Smith 18G fitted and he said it performed very well indeed. It made such great power he had to wind it back a little to give the gearbox a fighting chance. It was touching 380bhp but they settled for 360bhp and over 400lb/ft if I remember correctly.
My VF48 makes 334/381 on mine and that makes for such a fast road car it's crazy. The torque of the 2.5 makes it a great driving car once the boost is wound up. Very minimal lag too. |
Really impressed with what you're doing. I'm getting a load of ideas for my own wagon which has hardly had a new part for months...
|
Originally Posted by Cambs_Stuart
(Post 11838645)
Really impressed with what you're doing. I'm getting a load of ideas for my own wagon which has hardly had a new part for months...
|
After i wrapped the headers, i decided to spray them with DEI silicone spray, then wrapped them in aluminium exhaust tape.
LOL I was feeling a little paranoid that oil could drop onto the headers or uppipe, soak into the heat wrap and cause a fire hazard! Not as pretty as bare heat DEI titanium heat wrap, but hopefully functional! https://cimg7.ibsrv.net/gimg/www.sco...51a6b1ba2a.jpg |
All bits are on, but there is a water/coolant leak somewhere! :-(
Mechanic mate is going to come round sound to figure it out, and fix the leak. Not long now!! :-) |
Originally Posted by BrownPantsRacing
When Duncan mapped my hawkeye years back he'd just mapped a GB270 wagon with a Harvey Smith 18G fitted and he said it performed very well indeed. It made such great power he had to wind it back a little to give the gearbox a fighting chance. It was touching 380bhp but they settled for 360bhp and over 400lb/ft if I remember correctly.
My VF48 makes 334/381 on mine and that makes for such a fast road car it's crazy. The torque of the 2.5 makes it a great driving car once the boost is wound up. Very minimal lag too. By the way good work mate on the wagon interesting read:notworthy |
Originally Posted by Chef.gav
(Post 11852325)
Have you still got a cat in place mate? Iv got a vf48 in my hawk wagon sitting at 333/385lb and as you say makes a brilliant road car but I kept my prodrive cat in. Always wondered about another map and take the cat out! But then your just chasing bragging numbers !
By the way good work mate on the wagon interesting read:notworthy I'd changed the whole exhaust on my hawk and was using a cobra sports cat downpipe which achieved good results. I decided I wanted a fast every day car that I didn't have to worry about come MOT time and wasn't chasing numbers. I was very pleased with it indeed. I'm just about to fit a prodrive sports cat downpipe and few other bits to the FSTI now before mapping. Should be an interesting comparison! |
Originally Posted by Reshard1977
(Post 11852186)
All bits are on, but there is a water/coolant leak somewhere! :-(
Mechanic mate is going to come round sound to figure it out, and fix the leak. Not long now!! :-) |
Originally Posted by BrownPantsRacing
(Post 11852474)
Hurry up man! I want to see what it makes!!!!! :D
OK, suspension gone for tracking and alignment again, was out before. Now have a fast road set up, a little bit more aggressive than the Prodrive alignment/set up. Map and rolling road time paid for with Duncan/Racedynamix!! Not long now!! I'm feeling nervous! |
Any chance of a close up picture of where you installed the catch can? I've been struggling to place mine without it fouling on anything.
|
Hi All,
Been super busy with normal life and work (aka boring) stuff. I decided to go decat, and fit a k&N Typhoon in wing kit (for the sound, love the voice of the turbo!) and get the map from Duncan to suit. More pics on the way. Here is the graph! Also made 410 lbs/ft torque! https://cimg8.ibsrv.net/gimg/www.sco...30b9d4558f.jpg https://cimg4.ibsrv.net/gimg/www.sco...304b68e3f4.jpg https://cimg5.ibsrv.net/gimg/www.sco...c5d6726294.jpg |
Treated the wagon to an upgrade from the Godspeed big brake kit for WRX's to Ksports!
https://cimg2.ibsrv.net/gimg/www.sco...ac952dc7d6.jpg https://cimg3.ibsrv.net/gimg/www.sco...47aea193fc.jpg https://cimg4.ibsrv.net/gimg/www.sco...fac4431d90.jpg |
Also decided to remove the BC coilovers and fit KYB's with wagon specific blue prodrive springs :-)
|
All times are GMT +1. The time now is 01:54 PM. |
© 2024 MH Sub I, LLC dba Internet Brands