What mods have you done this week?
#362
Scooby Regular
#365
Watched a youtube video showing you can use normal spray cans not heat paint.
got this paint on eBay. Just heated up the part with heat gun , laid on a couple of coats (goes on quite uneven, very unlike normal rattle can paint) then blast with heat gun till it wrinkles up. Some bits wrinkle more than others, I'm guessing because of how uneven the paint goes on. So if u can master the application of the paint the end result is better.
#366
Scooby Regular
got this paint on eBay. Just heated up the part with heat gun , laid on a couple of coats (goes on quite uneven, very unlike normal rattle can paint) then blast with heat gun till it wrinkles up. Some bits wrinkle more than others, I'm guessing because of how uneven the paint goes on. So if u can master the application of the paint the end result is better.
#368
Scooby Regular
Centre trim change
After 2 years the vent piece started to bubble wasn’t too bad but not good enough for my car
so I got another set and had it resprayed in anthracite to break up the carbon dipped look I’m very pleased with it for the moment
Few pics as alwYs
You can see the bubbling on the left vent side most
Till next time...
so I got another set and had it resprayed in anthracite to break up the carbon dipped look I’m very pleased with it for the moment
Few pics as alwYs
You can see the bubbling on the left vent side most
Till next time...
#371
Scooby Regular
#373
Scooby Regular
iTrader: (1)
Uggggggghhhhhhh. When a solution causes another problem. Replaced the boot seal today, however one of the poxy boot strut fixings has fallen apart inside the boot lid and now I can't screw it back down.
Any ideas guys? I'm at a loss on this one as you can't access the inside of the wagon boots in any way at all and now have a broken strut pus a rattling nut inside it
Edit. Took the plastic trims off the inside of the boot lid off and managed to get the strut nut out. Not just need to figure out how to weld it back on INSIDE the flipping boot lid , what an absolutely crap design.
Edit 2. Ended up drilling the nut hole out so the nut fits inside then welding around the nut to fix it again, then put some touch up pain over it to cover the bare metal back up. Hardly ideal having to do all that but it's done now.
Any ideas guys? I'm at a loss on this one as you can't access the inside of the wagon boots in any way at all and now have a broken strut pus a rattling nut inside it
Edit. Took the plastic trims off the inside of the boot lid off and managed to get the strut nut out. Not just need to figure out how to weld it back on INSIDE the flipping boot lid , what an absolutely crap design.
Edit 2. Ended up drilling the nut hole out so the nut fits inside then welding around the nut to fix it again, then put some touch up pain over it to cover the bare metal back up. Hardly ideal having to do all that but it's done now.
Last edited by Fishbowlhead; 05 April 2018 at 02:59 PM.
#374
Scooby Regular
^ U soldier
#375
Scooby Regular
[QUOTE=Moley;11961604]Not an Impreza unfortunately, but fitted an OMP steering wheel and modified gear shifter to my Clio track car
Molly,
Which Clio is this? I have a 197 sat around doing nothing. I’m tempted to strip it out completely. Spend little money on modding it. Then just thrash it on track. I would be curious to know which model you have, how you find it on track? Is yours heavily modded as well? I really don’t want to chuck a load of cash at it but then don’t want to get rid of either. Could be a nice little cheap toy!?!?!?! What do you think?
Molly,
Which Clio is this? I have a 197 sat around doing nothing. I’m tempted to strip it out completely. Spend little money on modding it. Then just thrash it on track. I would be curious to know which model you have, how you find it on track? Is yours heavily modded as well? I really don’t want to chuck a load of cash at it but then don’t want to get rid of either. Could be a nice little cheap toy!?!?!?! What do you think?
#376
[QUOTE=R666ORY+1;12004882]
The car is a normal 172
It's had quite a few mods - but with DS2500 pads, Brembo HC discs, lowering springs and decent tyres that's all you need as a base for good fun track car.
It isn't the quickest, but it's probably the most fun I've had on track.
Not an Impreza unfortunately, but fitted an OMP steering wheel and modified gear shifter to my Clio track car
Molly,
Which Clio is this? I have a 197 sat around doing nothing. I’m tempted to strip it out completely. Spend little money on modding it. Then just thrash it on track. I would be curious to know which model you have, how you find it on track? Is yours heavily modded as well? I really don’t want to chuck a load of cash at it but then don’t want to get rid of either. Could be a nice little cheap toy!?!?!?! What do you think?
Molly,
Which Clio is this? I have a 197 sat around doing nothing. I’m tempted to strip it out completely. Spend little money on modding it. Then just thrash it on track. I would be curious to know which model you have, how you find it on track? Is yours heavily modded as well? I really don’t want to chuck a load of cash at it but then don’t want to get rid of either. Could be a nice little cheap toy!?!?!?! What do you think?
It's had quite a few mods - but with DS2500 pads, Brembo HC discs, lowering springs and decent tyres that's all you need as a base for good fun track car.
It isn't the quickest, but it's probably the most fun I've had on track.
#380
Scooby Regular
Join Date: Nov 2005
Location: m25 and surroundin areas......need 500+horses again!!!
Posts: 200
Likes: 0
Received 0 Likes
on
0 Posts
Odd jobs complete:
Removed the front splitter as i couldn't get over the speed bumps
Gearbox and rear diff oil change. It still looked like honey and new. Thats it for 5 years now
Removed the dust cover from under the bonnett as it was annoying me
Removed the front splitter as i couldn't get over the speed bumps
Gearbox and rear diff oil change. It still looked like honey and new. Thats it for 5 years now
Removed the dust cover from under the bonnett as it was annoying me
#381
Scooby Regular
I removed my dust cover about a month ago it was hanging down in bits
#382
Scooby Regular
Join Date: Dec 2013
Location: Nowhere
Posts: 211
Likes: 0
Received 0 Likes
on
0 Posts
Alcons are coming off today for some OEM brembos rebuilt and finished in red so that I can fit these bad boys over them...
Should feel fresh with brand new tyres, brakes and fluid