Smurf's Scooby
#1
Scooby Regular
Thread Starter
Smurf's Scooby
Thought I should start a thread and introduce myself to the guys and girls on here. My names Chris Murphy from Glasgow (Feel free to add me on facebook.) I bought my 1st Impreza almost a month ago now. It's a big step up from my Glanza which I thought was quick, but this car is on another level. no more useless power spinning away from the front end, just good old fashioned grip lol I'm obviously biased but I would say its immaculate. Probably the reason I wash it every time I get the chance. It used to belong to a member on here called EvoRach and you can tell its been well looked after. Changed the oil & filter for the 1st time at the weekend. Fuchs Titan Race Pro 5w-40. Also got some pink Sti valve caps from Scoobyparts.com.
Last edited by DJ Dunk; 19 June 2014 at 02:33 PM. Reason: Fix pic embedding
#2
Welcome Chris. I'm a Glasgow boy too.
Nice motor. You got any plans for it?
Scoobies are funny; when you get one and then drive something else it's like nothing compares to it. I've had my bug from new since 2001 and it's never skipped a beat after 117k miles.
Look after it mate and you'll never look back. All the best.
Nice motor. You got any plans for it?
Scoobies are funny; when you get one and then drive something else it's like nothing compares to it. I've had my bug from new since 2001 and it's never skipped a beat after 117k miles.
Look after it mate and you'll never look back. All the best.
#4
Scooby Regular
Thread Starter
Got my car booked in at Andy Forrest in September. Could've been August but im working away. If you read the spec of my car it is supposedly running 365bhp but i plan to get that checked as well as get a low power mode. Im currently running a standard sti manifold but from the turbo back is full stainless. What i want to know is will i get more power if i upgrade the manifold ?? Does it matter if i fit the manifold before the map and if i do fit it am i best to do so as close to mapping day as the car will have been mapped with current manifold. ?? Car is still on standard turbo.
Cheers guys
Cheers guys
#6
Scooby Regular
Thread Starter
Realised i didn't put the spec up
As it stands the spec is as follows:
365bhp 345lb/ft
Walbro 255 Uprated Fuel Pump
HDi Front Mount Intercooler with hardpiping relocated by GR Performance and powder coated in red by Two Brothers Coating.
Battery relocated to boot by GR performance.
Roger Clark Motorsport filter and trumpet
Japspeed Exhaust*
3 inch downpipe, decat
356mm K Sport 8 pot brake kit on front with Orangestuff pads
316 godspeed rear grooved discs with brembo calipers and Ferrodo DS32500 pads
18inch OZ Racing Alloys
Exceedy organic clutch and forged lightened flywheel
Gates timing belt fitted less than 1000 miles ago
RBF600 brake fluid
Toyo T1R tyres
Varta blue battery, less than a year old.
Front Strutbrace
BC BR Racing Coilovers
Whiteline Rear Anti Roll Bar
Whiteline Front Anti Roll Bar
Whiteline Anti Lift Kit
Whiteline alloy front drop links
Whiteline alloy rear drop links
Side Pillar Boost and Oil Temp Gauges
Carbon fibre mirrors
Lester front bumper
Front and Rear Tints
Front and Rear Tints
Alloytop engine mount
Sabelt steering wheel
Zero sports slam panel
Carbonfibre Alternator Cover
As it stands the spec is as follows:
365bhp 345lb/ft
Walbro 255 Uprated Fuel Pump
HDi Front Mount Intercooler with hardpiping relocated by GR Performance and powder coated in red by Two Brothers Coating.
Battery relocated to boot by GR performance.
Roger Clark Motorsport filter and trumpet
Japspeed Exhaust*
3 inch downpipe, decat
356mm K Sport 8 pot brake kit on front with Orangestuff pads
316 godspeed rear grooved discs with brembo calipers and Ferrodo DS32500 pads
18inch OZ Racing Alloys
Exceedy organic clutch and forged lightened flywheel
Gates timing belt fitted less than 1000 miles ago
RBF600 brake fluid
Toyo T1R tyres
Varta blue battery, less than a year old.
Front Strutbrace
BC BR Racing Coilovers
Whiteline Rear Anti Roll Bar
Whiteline Front Anti Roll Bar
Whiteline Anti Lift Kit
Whiteline alloy front drop links
Whiteline alloy rear drop links
Side Pillar Boost and Oil Temp Gauges
Carbon fibre mirrors
Lester front bumper
Front and Rear Tints
Front and Rear Tints
Alloytop engine mount
Sabelt steering wheel
Zero sports slam panel
Carbonfibre Alternator Cover
Trending Topics
#9
Scooby Regular
Thread Starter
No issues at all runs like a dream. Paid bout 2k over the odds tho. Wouldnt have bought anything from them had i not got in touch with the previous owner. They are a very shady place. Paid for the car signed everything over to find out it was sold as track car with no tax. Had to put 6 month on it. Dirty James Blunts. !!!
#10
Scooby Regular
Join Date: Jul 2007
Location: Bradford
Posts: 1,351
Likes: 0
Received 0 Likes
on
0 Posts
No issues at all runs like a dream. Paid bout 2k over the odds tho. Wouldnt have bought anything from them had i not got in touch with the previous owner. They are a very shady place. Paid for the car signed everything over to find out it was sold as track car with no tax. Had to put 6 month on it. Dirty James Blunts. !!!
Enjoy the car
#14
Looking good there mate, 365 on a VF35 is very good as usually you need to port the headers, inlet and maybe run a billet compressor wheel or a meth mix to acheive those figures.
Most STis, and a number of others, in standard form usually have a limiter 1000rpm below the guided redline for safety reasons i.e. tyres, etc. As yours is running 365hp you would probably see 165-170mph out of it but would be circa its limit (engine wise, the gearing is fine for speeds of around 200mph).
Regards,
Subaru Collector 555.
Most STis, and a number of others, in standard form usually have a limiter 1000rpm below the guided redline for safety reasons i.e. tyres, etc. As yours is running 365hp you would probably see 165-170mph out of it but would be circa its limit (engine wise, the gearing is fine for speeds of around 200mph).
Regards,
Subaru Collector 555.
Last edited by User 21721; 19 July 2014 at 05:12 PM.
#15
Scooby Regular
Thread Starter
Could well be less im only goin by piston heads advert. Said mapped to 365bhp n 345ft/lbs at some performance place. No dyno pront out to prove. Ther is an older dyno printout in the paperwork that says 345bhp and i think it was 365ft/lbs. mabey a mix up or a more recent map. even at 345 bhp it feels quick.
#16
Could well be less im only goin by piston heads advert. Said mapped to 365bhp n 345ft/lbs at some performance place. No dyno pront out to prove. Ther is an older dyno printout in the paperwork that says 345bhp and i think it was 365ft/lbs. mabey a mix up or a more recent map. even at 345 bhp it feels quick.
Regards,
Subaru Collector 555.
#17
Scooby Regular
iTrader: (8)
very nice car bud. im in scotland as well. 365 is the top end of what a vf35 will give so if it is running that power then nice one! i have a bug sti and im hoping to get a session with andy f soon to see what mine is running and maybe up the power a bit as ive got ported headers decat and induction to go on. mine has paperwork saying its had an ecutek remap to 300 bhp so quite a conservative map but does feel quick at that power now that i replaced the boost pill which ra motorsport discovered was missing lol. its boosting around 1.2-3 bar with a 1mm pill in place and pulling like a train and afr,s etc look spot on using dash command to check lambda. would be well chuffed if my 35 gave that sort of power! enjoy her m8.
#20
Scooby Regular
Thread Starter
Cars been to Andy Forrest. 355bhp 352 torque. With a gd few extra pops and bangs. Have 270 odd on low. Really happy. Think boost is 1.4 and 0.5.
#22
Scooby Regular
Thread Starter
Wasnt less than 8. Been in touch with previous owner since buying it. **** happens when u buy from a dealer. You would lose more depreciation on a new corsa lol. Was the best blobeye one for sale at the time. Couldve waited a month or 2. Saved a bit. But i wanted it ther n then. Just impatient.
#23
Scooby Regular
iTrader: (2)
Join Date: Dec 2004
Location: East Sussex
Posts: 1,106
Likes: 0
Received 0 Likes
on
0 Posts
Nice looking car and with some nice mods. 355 makes for a very quick road car. Looks like you had a bit of a touch with the number plate too, unless its a private one, looks like your name from a distance!
#24
Scooby Regular
Thread Starter
Yea cheers mate its fast enough lol. Was gonna buy SM03 URF. But it was 1300 just couldn't justify it. Would rather spend that on bigger turbo.
#25
Scooby Regular
Thread Starter
Okay guys, Little update as it's been a while,
Car now has an SC42 which has been upgraded by Owen Developments.
To help this along I've got a set of GT-Spec headers and a harvey up-pipe.
To help fuel it I have a set of Power Enterprise 800cc Injectors and Sytec FPR.
Also fitted a Turbosmart 3 Port boost solenoid.
I have no idea what to expect from this set up, on the previous set up I took it to the Dyno at Ecotune in Glasgow and ran 334bhp/332ft/lbs. I later found this was with two loose spark plugs.
I have the car booked into Andy Forrest on April 1st for mapping, so i will let you guys know what it makes then.
Car now has an SC42 which has been upgraded by Owen Developments.
To help this along I've got a set of GT-Spec headers and a harvey up-pipe.
To help fuel it I have a set of Power Enterprise 800cc Injectors and Sytec FPR.
Also fitted a Turbosmart 3 Port boost solenoid.
I have no idea what to expect from this set up, on the previous set up I took it to the Dyno at Ecotune in Glasgow and ran 334bhp/332ft/lbs. I later found this was with two loose spark plugs.
I have the car booked into Andy Forrest on April 1st for mapping, so i will let you guys know what it makes then.
#27
Scooby Regular
Thread Starter
Ok ,
So new turbo got mapped Friday, as you can see a gd bit more lag than the vf35 it replaced but when it wakes up it certainly pulls much better,
May have got a better result with ported oem headers, but thts hindsight for ya,
Doesnt drop off boost between shifts atall must be the ball bearing turbo
So new turbo got mapped Friday, as you can see a gd bit more lag than the vf35 it replaced but when it wakes up it certainly pulls much better,
May have got a better result with ported oem headers, but thts hindsight for ya,
Doesnt drop off boost between shifts atall must be the ball bearing turbo
#30
Scooby Regular
Matt.